Network (enabled) - Network setup MessEna - help message removed SetIPFlags - help message removed SetDHCPSIP - help message removed SetRouterIP - help message removed SetIPMask - help message removed SetIPAddress - help message removed SetEthernet - help message removed SetNetDefaults - help message removed NetSaved - help message removed NetCurrent - help message removed CONSOLE:> setipaddress usage: SetIPAddress IPaddr.a IPadr.b IPaddr.c IPaddr.d CONSOLE:> setipaddress 192 168 0 33 CONSOLE:> CONSOLE:> netcurrent Network Device: LAN96 Device Ethernet Address(hex): 00:00:c4:0a:d6:2e Device IP Address: 0.0.0.0 Device IP Mask: 0.0.0.0 Device Router IP: 0.0.0.0 CONSOLE:> netsaved Ethernet Address(hex): 00:00:c4:0a:d6:2e DHCP Server: 255.255.255.255 Network Flags: 0x0009 NO Router IP DHCP client active CONSOLE:> setipflags usage: SetIPFlags R|N [F|B|D] CONSOLE:> setipflags F Unrecognized first flag: F usage: SetIPFlags R|N [F|B|D] CONSOLE:> setipflags R F CONSOLE:> netsaved Ethernet Address(hex): 00:00:c4:0a:d6:2e IP Address: 192.168.0.33 IP Mask: 255.255.255.0 Default Router: 224.0.0.2 Network Flags: 0x0002 IP address fixed CONSOLE:> netcurrent Network Device: LAN96 Device Ethernet Address(hex): 00:00:c4:0a:d6:2e Device IP Address: 0.0.0.0 Device IP Mask: 0.0.0.0 Device Router IP: 0.0.0.0 CONSOLE:> setipaddress 192 168 0 33 CONSOLE:> CPU2000 Boot Loader Version: 2.0 RC2 Build#: 11 (Nov 20 2009) ETC Test: EPHSR Wrong Reset value - Disconnect cable CPU flash size: 2097152 (0x200000) Bytes CPU RAM size in use: 1048576 0x(100000) Bytes CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> betcurrent betcurrent: unknown command CONSOLE:> netcurrent Network Device: LAN96 Device Ethernet Address(hex): 00:00:c4:0a:d6:2e Device IP Address: 192.168.0.33 Device IP Mask: 255.255.255.0 Device Router IP: 224.0.0.2 CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> help network Network (enabled) - Network setup MessEna - help message removed SetIPFlags - help message removed SetDHCPSIP - help message removed SetRouterIP - help message removed SetIPMask - help message removed SetIPAddress - help message removed SetEthernet - help message removed SetNetDefaults - help message removed NetSaved - help message removed NetCurrent - help message removed CONSOLE:> netsaved Ethernet Address(hex): 00:00:c4:0a:d6:2e IP Address: 192.168.0.33 IP Mask: 255.255.255.0 Default Router: 224.0.0.2 Network Flags: 0x0002 IP address fixed CONSOLE:> netcurrent Network Device: LAN96 Device Ethernet Address(hex): 00:00:c4:0a:d6:2e Device IP Address: 192.168.0.33 Device IP Mask: 255.255.255.0 Device Router IP: 224.0.0.2 CONSOLE:> setipaddress 192.168.0.3 usage: SetIPAddress IPaddr.a IPadr.b IPaddr.c IPaddr.d CONSOLE:> setipaddress 192 168 0 3 CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> netcurrent Network Device: LAN96 Device Ethernet Address(hex): 00:00:c4:0a:d6:2e Device IP Address: 192.168.0.33 Device IP Mask: 255.255.255.0 Device Router IP: 224.0.0.2 CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> setnetdefaults CONSOLE:> CONSOLE:> help network Network (enabled) - Network setup MessEna - help message removed SetIPFlags - help message removed SetDHCPSIP - help message removed SetRouterIP - help message removed SetIPMask - help message removed SetIPAddress - help message removed SetEthernet - help message removed SetNetDefaults - help message removed NetSaved - help message removed NetCurrent - help message removed CONSOLE:> CONSOLE:> setnetdefaults CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> header *** $$$ This is the Boot Loader program $$$ *** Image Check field: 0x7bb188f4 Image file check field (as received from HOST): 0x00000000 Product Name: CPU2000 Boot Loader Product Version: 2.0 RC2 Product Serial Number as stored in NVRAM: Serial Number Uninitialized Product CPU ID from Hardware: 2 Personality ID from Hardware: 24 ProductID from Hardware: 0 Image Load Address: 0x000000 Image End Address (after last): 0x03EEF0 Image Entry Address: 0x012C0C CONSOLE:> CONSOLE:> CONSOLE:> CONSOLE:> help IButton (enabled) - Commands for controlling iButton reconfigIbutton - Reconfigures Ibutton swaplampandcell - Swaps lamp and cell address cellWettMatEnum - Set wet material enumeration celltypeEnum - Set type enumeration cellpartnum - Set Part Number cellVer - Set Flow Cell ID Struct cellsernum - Set Serial Number cellvolume - Set Volume cellWetMat - Set Flow Cell Wetted material cellpl - Sets the number of ignitions celltype - Set Lamp on in Min lampVer - Set Version to Buffer lampFailedIg - Sets the number of failed ignitions lampGoodIg - Sets the number of good ignitions lampMin - Set Lamp on in Min WriteFlowCell - Write Flow Cell Data from Buffer to Memory WriteLamp - Write Lamp Data from Buffer to Memory DumpFlowCellMemory - Dump Flow Cell Memory DumpLampMemory - Dump Lamp Memory PassWord - Set Password iBInit - Initialize the iButton iBPresent - Check the presence of an iButton iBRead - Read data from the iButton iBWrite - Write data to the iButton iBFormat - Init the iButton memory iBTest - Test iButton data write/read TempController (enabled) - Commands for manipulating the Heater Managers tcsetpoint - Sets the temp update rate tcoutput - Set the RTD current source calibrate values tcstate - Sets set to OFF,AUTO,MANUAL controller (enabled) - Controller commands shutterIdleMode - Sets shutter Idle Mode setTempCont - Sets the temperature controller range setFcConfig - Enable and disables lamp and FC ID setLampConfig - Enable and disables lamp and FC ID resetlamphist - Reset lamp hist resetDiag - Dump dark counts stime - set the time disabletempcontrol - disable temp. control setinstrumenttype - set instrument type getDiagData - get diagnostic data setParam - set Parameter getParam - get Parameter LeakDetector - Enable Leak Detector runScan - run Scan runCalibration - run Calibration runNoiseTest - run Noise Test resetNVRam - reset NVRam resetInstrument - reset Instrument getDiagResults - get Diag Results getComAlarm - Get Com Alarm sc - Capture the current screen setserialnumber - Set the Instrument Serial Number time - Display time since powerup in seconds methoddump - Dump Method Data scandump - Dump scan data and stats doscan - perform wavelength scan noiseEnd - Recycles the noise buffer noisedump - Dump raw data and stats noisequery - Query Noise Test noisestart - Start Noise Test autoZero - AutoZero Channel lampOff - Turn Lamp OFF lampOn - Turn Lamp ON setsensitivity - Set the channel sensitivity(s) in AUFS setfiltertc - Set channel filter time constant(s) analog - Turn Switch OFF switchOff - Turn Switch OFF switchOn - Turn Switch ON getclockstring - Get Date and Time updateStatus - Update Remote Status mi - Minimize Initialization Time minimizeInit - Minimize Initialization Time raiseAlarm - Raise a fatal alarm setAZWavelength - Set AZ On Wavelength Change syscal - Launch Calibration CAP sysinit - Launch Initialize CAP setDual - Set Dual Wavelength Mode setSingle - Set Single Wavelength Mode lock - Set Lock remote - Set Remote setWavelength - Set Wavelength(s) abortCap - Stop and Abort cap if running AcqMan (enabled) - Commands for AcqMan darkOffset - Modify dark offset resumeAcqmanState - resume AcqMan State setAcqmanIdle - set AcqMan Idle xread - read A/D acq? - print energies to the terminal acqEmit - print energies to the terminal HgCal - find Hg peaks ChangeAndAcquire - Test filter motor settling MoveAndAcquire - Test grating motor settling Filterpos - set the optical filter to a position ScanFilter - Scan the optical filter positions findHomePeak - find 656 nm initAcq - initialize transducers scan - Scan a range of grating steps calGrating - Calibrate the Grating Positions AutoGain - Find optimum full scan gain TestCalc - Test Grating calculation time Transducer (enabled) - QSPI transducer Diagnostics xdWrite - Write a register in a serial device xdRead - Read a register from a serial device LeakTest - Test A/D front end quality QADCTest - Test ADC channels xCalibrate - Calibrate transducers xFilter - Set filter/sampling freqency xGain - Set trasducers gain xSync - Synchronize transducers xReset - Reset transducers RunSlots - Run QSPI slots FillSlot - Fill QSPI slot Positioner (enabled) - Commands to manipulate positioners pRange - Enable/Disable range checking pBlash - Measure and set backlash pHome - Home the positioner pStep - Move the positioner in steps pMove - Move the positioner pSweep - Cycle between two positions Motor (enabled) - Commands for manipulating motors mSetMoveC - Set Move current for the driver mGetT - Get move time for the motor mRnd - Random moves of the motor mCyc - Cycle the motor mStp - Stop the motor mMovC - Start continuous move of the motor mMovR - Relative raw move of the motor mMov - Move the motor to raw position mSetB - Set the raw motor backlash mSetSV - Set motor slew velocity mSetV - Set the motor velocity mSetP - Set the raw motor position mOff - Turn the motor off mDelete - Delete last TSM motor mCreate - Create new TSM motor mMode - Set Sync(default)/Async move mode Sensor (enabled) - Commands for manipulating Sensors sChanges - List sensor changes during motor move sWait - Wait for the sensor to reach a state sPos - Read the sensor value (mapped position) sState - Read the sensor state sSimulate - Start using simulated values for the sensor NVFile (enabled) - Commands for NVRAM file system NVFDriveFormat - Reformat the NV Drive file system NVFReset - Reset the NVRAM Drive file system NVFClear - Clear the NVRAM file buffer NVFDump - Dump NVRAM file to stdout NVFTrace - Redirect Trace to nvTrace file Utilities (enabled) - Service Utilities sc - Screen Capture to the stream Jumpers - Displays software jumpers ShowSerial - Show Serial Number SetSerial - Save Serial Number in NVRAM GO - Start arbitrary function in memory BinMode - Switch Terminal to Binary mode SetProductID - Save ProductID in ETC EEPROM Header - This Program Header Flash - Show flash size DIAG (enabled) - Commands for manipulating DIAG DiagSetCode - Sets the diag check code DiagDump - Dump diagnostics results DiagRun - run the diagnostics Network (enabled) - Network setup NetStats - Print Network Statistics MessEna - Enable Network Messages SetIPFlags - Save IP Flags in EEPROM SetDHCPSIP - Save BOOTP/DHCP Server IP in EEPROM SetRouterIP - Save Router IP Address in EEPROM SetIPMask - Save IP Subnet Address Mask in EEPROM SetIPAddress - Save IP Address in EEPROM SetEthernet - Save Ethernet Address in EEPROM SetNetDefaults - Set Network Addresses to defaults NetSaved - Show Network Addresses saved in EEPROM NetCurrent - Show current Network Addresses in use Memory (enabled) - Commands for managing the dynamic memory system poke - Writes a memory address peek - Displays memory in hex and ASCII checkSum - calculate check sum MemStat - Memory pool status vrtx (enabled) - VRTX task management taskstats - Display task statistics setpriority - Set a task's priority resume - Resume a suspended task suspend - Suspend a task launch - Launch a constructed task taskname - Get a task's name tid - Get a task's ID stack - Get stack usage statistics taskstatus - Get the tasks status priority - Get a tasks priority slice - Enables/Disables round robin scheduling DumpVRTX - Display VRTX parameters ISR (enabled) - Commands for debugging ISRs IRQDump - dumps ISR IRQ Info ISRDump - dumps ISR Info Tpu (enabled) - Commands for the TPU DIOlevel - Get/Set the DIO channel level DIOCreate - Create the DIO channel SpwmLevel - Force a level on the SPWM pin SpwmSet - Set the Spwm Pulse Parameters SpwmCreate - Create Spwm channel PWMSet - Set the PWM Pulse Parameters PWMCreate - Create PWM channel tpuChIntTest - Test the TPU ChanInt by toggling LEDs tpuChanInt - Get/Set the TPU channel Interrupt tpuChanPri - Get/Set the TPU channel priority tpuChanStStop - Start/Stop the TPU channel tpuChanHSRQ - Get/Set the TPU Test channel HSQ & HSR tpuChanSetRAM - Set the TPU channel RAM tpuChanCreate - Create the TPU Test channel tpuChanDelete - Delete the TPU channel status (enabled) - Status/Tracer commands disabletraceattr - Enable trace attribute enabletraceattr - Enable trace attribute dumptracers - Dump tracer information dumpcodes - Dump information on all status codes statuscode - Dump information on a single status code gettracelevel - Get the TRACE level for a group settracelevel - Set the TRACE level for a group disablecode - Disable Status code enablecode - Enable Status code disable - Disable Trace output enable - Enable Trace output listgroups - List installed Status groups listtracers - List all the tracers names DataVar (enabled) - Commands for manipulating DataVars dataWatch - Watch a Data Var Info - info on the data Show - show the data Edit - edit the data Set - set the data Component (enabled) - commands that manipulate components idle - idle the component startupDiag - run the startup diagnostics validate - validate the component conifg hookup - hookup the component reset - Reset the component dump - Dump a component listtype - List component names by type list - List all the component names cmdmon (enabled) - Command monitor built-in commands editKeys - List the command line edit keys version - Report the application version cmdmon - Manage the cmdmon attributes package - Manage the installed packages help - Print this table unalias - Remove a command alias alias - Create a command alias repeat - Repeat the following command cat - Runs each of its arguments as a command sleep - Delay execution by seconds freespawnedthreads - free any threads created with the spawn command spawn - spawn the following command as a thread Initialization Completed.