ThermoFisher.CommonCore.WpfPlot

Forms designer attributes, related to amplification.

Gets or sets amount to amplify the selected region

Gets or sets a value indicating whether amplification is enabled.

Gets or sets a value indicating whether all amplifiers should be cleared

Gets or sets a value indicating whether a selected region should be cleared

Class to convert peaks from the peak detector into peak labels and markers

Gets or sets the color of peak label text

Gets or sets the color of peak label lines, including boxes or joining lines

Gets or sets the thickness of peak label lines, including boxes or joining lines

Gets or sets a value indicating whether to enable smoothing (ant-alias) of peak label joining lines

Gets or sets a value indicating whether to enable blending of peak label joining lines, as they approach the peak

Gets or sets a percentage indicating how much of the diagonal part of elbow markers is protected against collisions (with other labels). If this is set "0" ensure (by brush selection) that these lines have higher transparency. Setting to "10" would allow the 10% of the line nearest a peak being labeled to overlap.

Gets or sets the decimal places for peak labels. Used for areas and Heights.

Gets or sets a value indicating whether to label with retention time of detected peak

Gets or sets a value indicating whether to label peaks with area

Gets or sets a value indicating whether the peak area is in E format (1.0E5)

Gets or sets the decimal places for peak area label in exponential format

Gets or sets a value indicating whether to label peaks with area

Gets or sets a value indicating whether to label peak with peak height

Gets or sets a value indicating whether the peak height is in E format (1.0E5)

Gets or sets the decimal places for peak height label in exponential format

Gets or sets a value indicating whether the label peaks with signal to noise ratio

Gets or sets a value indicating whether to label peaks with component name

Gets or sets a value indicating whether to put a box around the label text

Gets or sets a value indicating whether permit elbows (routing) of lines to offset peaks. This permits more peaks to be labeled.

Gets or sets how many paths tried for elbow markers: controls. Maximum: 6. Default: 6. Larger values permit longer vertical lines down from the label (and shorter diagonal lines)

Gets or sets a value indicating whether to permit peak labels to be placed below the peak apex This permits more peaks to be labeled.

Gets or sets a value indicating whether to rotate peak label text

Gets or sets color to use for baseline of filled peaks

Gets or sets color to use for outline of filled peaks

Gets or sets color to fill peaks with

Gets or sets symbol drawn at peak baseline ends

Gets or sets a value indicating whether to label peaks with base peak mass

Gets or sets a value indicating whether to label peaks with mass to charge

Gets or sets the precision to use with base peak labels

Gets or sets the precision to use with times in labels

Gets or sets the text to show for RMS noise units

Gets or sets the prefix for signal to noise labels, where the is a numeric value. Default "SN:"

Gets or sets the prefix for system suitability labels "SU:"

Gets or sets the message shown for signal to noise labels, when there is no measured noise. Default SN: INF

Gets or sets the message shown for signal to noise labels, when no noise has been calculated Default "SN: NA"

Gets or sets the prefix for retention time labels on peaks. Default "RT:".

Gets or sets the prefix for scan number labels. Default "S#:"

Gets or sets the prefix for automatic baseline peak areas. Default "AA:"

Gets or sets the prefix for manual baseline peak areas. Default "MA:"

Gets or sets the prefix for automatic baseline peak heights. Default "AH:"

Gets or sets the prefix for manual baseline peak heights. Default "MH:"

Gets or sets the prefix for base peak mass. Default "BP:"

Gets or sets the prefix for mass to change. Default "m/z:"

Gets or sets the flag text for SuitabilityBaselineClipped. Default "Bc"

Gets or sets the flag text for SuitabilityColumnOverload. Default "Co"

Gets or sets the flag text for SuitabilityConcave. Default "Cc"

Gets or sets the flag text for Suitability Signal To Noise. Default "Sn"

Gets or sets the flag text for SuitabilityPeakWidth. Default Default "Pw"

Gets or sets the flag text for SuitabilityResolution. Default "Rs"

Gets or sets the flag text for SuitabilitySaturated. Default "St"

Gets or sets the flag text for SuitabilitySymmetry. Default "Sy"

Gets or sets the flag text for SuitabilityTailing. Default "Tl"

Gets or sets a value indicating whether or not to show suitability flags. Peaks passed in must implement ISystemSuitabilityResultsAccess. For example: Class PeakWithSuitability. Flags are shown for test fails BaselineClipped B ColumnOverload O Concave C Noise N PeakWidth W ResolutionCheck R Saturated S SymmetryCheck Y Tailing T

Initializes a new instance of the class. Default constructor

Gets or sets a value indicating whether the property "peak fill color" is used for PPD peaks. When false: PPD peaks are individually colored. It is recommended that this should be set "true" when applications have no merged PPD peaks.

Method to duplicate settings from another object. For example: If an "options form" is used to configure one plot, this could be used as part of an "apply to all" implementation for applying label changes to several plots on the same view.

Object who's properties are copies to this

Creates a new object that is a copy of the current instance.

A new object that is a copy of this instance. 2

Contains Start and End Points and Values of a Scrol Event and the Id of the control, that raised the Event

Initializes a new instance of the class. Create EventArgs for a Control Scrolled Event

Start of X range scrolled to End of X range scrolled to Id of the Control that raised the event

Gets the Control Identification Information (name, type, Id)

Gets the new scrolled region start Data Value

Gets the new scrolled region end Data Value

Information for 1 chromatogram traces

Gets or sets the points.

Gets or sets the peaks. This may be empty, but should not be null.

Gets or sets the title above trace. This may be null or empty.

Gets or sets the title to right. This may be null or empty.

Gets or sets the mass precision, used for the base peak mass labels for this trace.

Gets or sets the label options.

Initializes a new instance of the class.

Real size units, (accepted by emf exports)

Not a known unit. Approx 1/100 inch

Inches

Millimeters

Methods to create clipboard data or files in various formats.

Copy the last drawn plot to the clipboard, with a specified image size

A dependency object which may be used to create a windows handle Graph to copy The clipboard format. True if custom Size, false if display size. width in pixels (for custom size). 0 (default) if not custom height in pixels (for custom size). 0 (default) if not custom For EMF format: If set, output may contain alpha blended (transparent) lines

Copy the last drawn plot to the clipboard, with a specified image size

A dependency object which may be used to create a windows handle Graph to copy The clipboard format. True if custom Size, false if display size. unit of size, when specified width in size units (for custom size). 0 (default) if not custom height in size units (for custom size). 0 (default) if not custom For EMF format: If set, output may contain alpha blended (transparent) lines

Copy the last drawn plot to the clipboard as a bitmap, using the same size as on screen.

Graph to render scaling to apply to bitmap (current display DPI

Copy the last drawn plot to the clipboard, with a specified image size

Graph to render width in pixels height in pixels

Copy the last drawn plot to the clipboard, with a specified image size

Graph to render width in pixels height in pixels Scale to map from screen DPI

Copy the last drawn plot to the clipboard, using the same size as on screen

The window Handle. Graph to render If set, output may contain alpha blended (transparent) lines

Copy the last drawn plot to the clipboard, with a specified image size

handle of window Graph to render width in pixels height in pixels If set, output may contain alpha blended (transparent) lines

Copy the last drawn plot to the clipboard, with a specified image size. Image is rendered ti the nearest mm of the requseted size.

handle of window Graph to render width in supplied inits height in supplied units units of width and height If set, output may contain alpha blended (transparent) lines

Copy the last drawn plot to the clipboard, using the same size as on screen

Graph to render

Copy the last drawn plot to the clipboard, using the same size as on screen

Graph to render

Copy the last drawn plot to the clipboard, with a specified image size

Graph to render width in pixels height in pixels

Copy the last drawn plot to the clipboard, with a specified image size

Graph to render width in pixels height in pixels

Draw the last drawn plot as a bitmap.

Graph to render The width in pixels. The height in pixels. The .

Draw the last drawn plot as a bitmap.

Graph to render The width in pixels. The height in pixels. Scale to map from screen DPI. For example: Commonly {2.5, 2.5} for 4K Screens The .

Get a handle to the parent window

Current control or window The handle to the parent window

Create an EMF file (file made with WMF extension) File is same size as screen object

Graph to render Name of file to create If set, output may contain alpha blended (transparent) lines

Create an EMF file (file made with WMF extension) and specified image size (units 1/100 inch)

Graph to render Name of file to create Size of image to create (in units of 1/100 inch) If set, output may contain alpha blended (transparent) lines

Create an EMF file (file made with WMF extension) with specified image size in the specified units. Rendered image size is "to the nearest millimeter" of the requested size.

Graph to render Name of file to create Size of image to create in the given unit of measure unit of "size" If set, output may contain alpha blended (transparent) lines

Create an EMF file (file made with WMF extension) File is same size as screen object

Graph to render Name of file to create

Create an html file (file made with WMF extension) and specified image size (units 1/100 inch)

Graph to render Name of file to create Size of image to create (in units of 1/100 inch)

Create a clipboard bitmap.

Graph to copy True if using custom size. The width. The height. DPI used to correct bitmap size based on current window

Create a clipboard bitmap.

Graph to render True if using custom size. The width. The height.

Create a clipboard bitmap.

Graph to render True if using custom size. The width. The height.

Create a metafile on the clipboard, with size in specifed "real world" units.

A dependency object, used to make a window handle. Graph to copy The width. The height. units of width and height If set, output may contain alpha blended (transparent) lines

Create a metafile on the clipboard.

A dependency object, used to make a window handle. Graph to copy True if using a custom size. The width. The height. If set, output may contain alpha blended (transparent) lines

Draw this plot as an HTML string

Graph to render Bounding box A string containing HTML commands

Draw this plot as an HTML string

Graph to render Bounding box SVG daata

create meta file.

The graph. The file name. The size, in the given unit of measure. units of "size" The handle to device context. If set, output may contain alpha blended (transparent) lines

create meta file.

The graph. The file name. The size. The handle to device context. If set, output may contain alpha blended (transparent) lines

write metafile to stream.

The graph. The size, in the supplied unit of measure. Unit of measure The handle to device context. The stream. If set, output may contain alpha blended (transparent) lines

write metafile to stream.

The graph. The size. The handle to device context. The stream. If set, output may contain alpha blended (transparent) lines

draw graph as EMF.

The graph. The size. The graphics created from an image. If set, output may contain alpha blended (transparent) lines

Create temporary file containing a metafile.

Graph to render The width of the drawing in 1/100 inch The height of the drawing in 1/100 inch. The file name. The created metafile, from the open file. If set, output may contain alpha blended (transparent) lines

Create temporary file containing a metafile.

Graph to render The width of the drawing in 1/100 inch The height of the drawing in 1/100 inch. units of width and height The file name. The created metafile, from the open file. If set, output may contain alpha blended (transparent) lines

The find parent window.

The child. The .

Data sent when an annotation label is double clicked

Gets or sets the label selected

Creates a new instance of LabelDoubleClickedEventArgs from the supplied label

Label which was double clicked

Internal Class to assist controls with draggable markers

Constructor

Gets or sets the image being dragged

Gets or sets the label being dragged

Begin dragging

The shape

Begin dragging

The shape

An image (peak label) has been dragged, and placed. Calculate where it has been placed, and update it's position.

Tool to convert pixels to data values Defines where the mouse was released set if the mouse was moves since it went down

The ion map attributes.

Initializes a new instance of the class.

The attributes to copy. Thrown if the attributes supplied are null

Initializes a new instance of the class.

Gets or sets method of spectrum extraction

Gets or sets mass of parent

Gets or sets a value indicating whether to label more than just mass

Spectrum Extraction Mode (Precursor, Product or neutral)

Precursor scan

Product scan

Neutral scan

Do not update the spectrum on clicking in a map

Interaction logic for IonMapCompositeControl

IonMapCompositeControl

Initializes a new instance of the class.

Gets the ion map control.

Gets the ion map plot.

Gets the spectrum control.

Gets the spectrum plot.

The ion map control 1 ion map scan has changed.

The sender. The e.

The ion map control 1 ion map settings have changed.

The sender. The settings.

The ion map plot settings control 1 ion map settings have changed

The sender. The settings.

InitializeComponent

3D section of the ion map control. The controls needs 3 components: IonMapPlot, IonMapSpectrum and IonMapSettings

IonMapControl

convert boolean "visible" to visibility type.

Is control visible? Converted type

Initializes a new instance of the class.

The _undo manager.

Gets or sets Id data

Gets the object which renders the ion map.

Gets or sets a value indicating whether to paint the border round the CalibrationCurve Plot

Gets or sets a value indicating whether larger points are drawn (approximately elliptical) for higher intensities. Larger data is drawn first, with small data overlaid. This option makes it easier to see peaks in the density map, at the expense of resolution.

Gets or sets a value indicating whether panning has been enabled

Gets or sets a value indicating whether the control is waiting for annotation

Gets or sets the color of the border when the control is unselected

Gets or sets the color of the border when the Control is selected

Gets an objects used to translate mouse position to data position. This is read only, as it is set on construction.

Gets or sets the cursor pick

Gets or sets a value indicating whether the Undo/Redo feature is enabled.

The _enable context menu.

Gets or sets a value indicating whether the control's own Context menu is used. The Context Menu can be manipulated and added to by the Application using the control it contains certain basic functions, such as Reset Scaling etc.

Gets or sets a manager for setting heading information

Gets or sets an optimization parameter to limit the number of points created

The common constructor.

The id.

Save the current plot in the undo stack

Sets the Plot back to the last state before the last Do was called - Undoes changes

Sets the plot back into the state before an Undo was called (if there is one) - Redoes Undoes

Clear both UnDo and Redo Stacks

Apply undo redo.

The plot.

Pan interface

Target percentage to pan Direction to pan - either forward or backwards.

Pan interface

start of pan range end of pan range

Event handler for when a range is selected

The data provider selected Ranges Starting point selected Ranges Ending Point

Event handler for when a range is selected

The data provider selected Ranges Starting point selected Ranges Ending Point

A box range has ben selected.

The start. The end. The start region.

The product mass range selected.

The start. The end. The start region.

The precursor mass range selected.

The source. The start. The start region.

Make this plot "active"

Print Page

Rectangle bounds to print graphics to print

The creates a new spectrum plot, using the attached mapping data source, based on the spectrum attributes. An event IonMapSettingsChanged is fired after this. The event should be used to update the spectrum plot.

The settings to apply.

Add header

Where to add the header Text block representing the header Flag indicating whether to draw to the top Flag indicating whether to draw to the bottom.

Given a rectangle and graphic, draw a map

The bounds in which to draw the chromatogram The graphic area on which to draw the chromatogram

Create a spectrum based on the selected point

The data provider the precursor mass for the created spectrum the product mass for the created spectrum

Update the attached spectrum.

The data source. The mass.

Print the plot

Bounding rectangle Graphics to draw to

Mouse down handler

Event arguments

Start an adorner, which shows the region being zoomed by a line or box being dragged over a plot.

The mouse down point.

Construct the adorner

The region where the mouse was clicked. The style of the pick marker. The mouse down point.

Determine the correct color for the adorner

The path of the adorner. The color to use.

Calculate a color which will show up against the background of the plot.

The color to use (for an adorner)

Create cross hair cursor.

The point.

Render the pick marker.

The line draw. The color.

Remove any adorner I have created

The control's adorner layer

Mouse Move handler

mouse event args

Gets or sets the control size.

Gets or sets the clipboard copy format.

true if use custom copy.

Gets or sets a value indicating whether to use copy size and resolution from context menu"

The custom copy resolution.

Gets or sets the resolution DPI for custom copy feature"

The custom copy width.

Gets or sets width in pixels for custom copy feature"

The _custom copy height.

Gets or sets the height in pixels for custom copy feature"

Measure override.

The constraint. The .

Overrides the Controls Paint Handler (calls to base)

The drawing Context.

The reset scaling tool strip menu item was clicked.

The sender. The event args.

The redo tool strip menu item was clicked.

The sender. The event args.

The undo tool strip menu item was clicked.

The sender. The event args.

copy to clipboard tool strip menu item clicked. Perform copy.

The sender. The event args.

The chromatogram context menu strip was opened.

The sender. The event args.

chromatogram context menu strip is opening. Enable/disable menu items.

The sender. The event args.

Configure an undo redo feature.

The menu item to configure (show or hide). Set if undo/redo is enabled.

get menu item from context menu.

The context menu. The menu item name. The menu item with the name supplied

On mouse left button up.

The event.

End of activity of "cursor pick" (mouse went up)

Handle keyboard input

Event Arguments

Ion Map settings EventHandler

The on ion map settings changed.

The e.

Ion Map scan update EventHandler

The on ion map scan changed.

The e.

Graph Region Selected Event handler

The on graph region selected.

The event

Raise Control Selection Event

The on control selected.

The e.

EventHandler for catching, when Graph Scaling has been reset

The on reset scaling.

The e.

Expand vertical - Expand the MassRange by factor of 2

true if graph is changed

contract horizontal scale by a factor

true if graph is changed

Expand horizontal

true if graph is changed

contract vertical scale

True if graph was changed

Reset the scaling to the data max values

Gets a value indicating whether Control is currently selected

toggles the selection of the control

control that triggered the selection event event args for the event

InitializeComponent

Interaction logic for IonMapPlotSettingsControl

IonMapPlotSettingsControl

Initializes a new instance of the class.

Initialize the control

Settings for all fields in the control

Update the available text boxes.

convert nullable bool to boll, considering null as false.

The nullable bool. The .

The send ion map settings notification.

The mode.

Ion Map settings EventHandler

The on ion map settings changed.

The e.

The product spectrum radio button was checked.

The sender. The event.

The product spectrum radio button was unchecked.

The sender. The event args.

The precursor map radio button was unchecked.

The sender. The event args.

The precursor map radio button was checked.

The sender. The event args.

The neutral loss map radio button was checked.

The sender. The event args.

The neutral loss map radio button was unchecked.

The sender. The event args.

The precursor mass text box text changed.

The sender. The event args.

The product mass text box text changed.

The sender. The event args.

The neutral mass text box text changed.

The sender. The event args.

The extra mass label check box was checked.

The sender. The event args.

The extra mass label check box was unchecked.

The sender. The event args.

The do not update radio button is checked.

The sender. The e.

The do not update radio button is unchecked.

The sender. The e.

InitializeComponent

This class describes a spectrum, generated from an Ion Map data source

Gets or sets the raw file name

Gets a scan object to plot

Gets the definition of how this scan is created from an ion map

Initializes a new instance of the class. Create a scan for an ion map spectrum plot.

The scan data to plot Definition (heading data) for the scan

Class to signal that a new scan has been created from an ion map plot

Gets an IonMapScanUpdate object containing information about the update

Initializes a new instance of the class. Create arguments for the event "a new scan is ready to plot, created from an ion map"

Definition of the scan to plot

Class to send events between ion map 3d control, spectrum control, and settings form

Gets the ion map definition contained in the event

Initializes a new instance of the class. Create event arguments to pass ion map setting from a form to plot controls.

Settings to control the type of ion map spectrum plot

Special spectrum plot for ion maps

Initializes a new instance of the class.

Gets or sets the spectrum ion map settings.

set the scan to display

The file Name. scan to set the display to

Create a title, including the mass used to construct the spectrum

The file Name. Text defining mass (for example "Precursor") Mass for "massName", for example a precursor mass The time. The scan Number. A block of text for a title

this EventHandler is to automatically update the spectrum view when the corresponding IonMap has been clicked - just register this method to the IonMapPlotControls' IonMapScanChanged event

object that triggered the event EventArgs sent with the event

Defines data sent when a trace becomes selected.

Gets the selected trace

Initializes a new instance of the class.

The trace number selected

Contains Start and End Points and Values of a Panning Event and the Id of the control, that raised the Event

Initializes a new instance of the class. Create EventArgs for a Control Panned Event

Start Point where to pan End Point where to pan Start Value where to pan End Value where to pan Id of the Control that raised the event

Gets the Control Identification Information (name, type, Id)

Gets the pan Start in Pixel Coordinates

Gets the pan End in Pixel Coordinates

Gets the Pan Start as Data Value

Gets the Pan End as Data Value

Control for 3d map plot. Designed to give map in chromatogram style (time on X axis)

MapControl

The plot is selected.

The undo manager.

The _plot scroll bar support.

The m_cursor pick start point.

Is mouse captured?

The m_cursor cross hair.

The cursor pick.

Gets or sets the cursor pick

The header manager.

Gets or sets the Header manager

The id.

Gets or sets the control's Id data

The file map plot.

Gets or sets the object which draws the map. Cannot be set to null.

Gets or sets the cursor translator, which is used to translate mouse position to data position.

true if there is pending annotation.

Gets or sets a value indicating whether the control is waiting for annotation

The on property changed.

The e.

True if the control is enabled to do auto range selection handling.

Gets or sets a value indicating whether or not the default GraphRegionSelectionEvent is automatically handled. Registers and unregisters the default method for Event Handling of GraphRegionSelection

Gets or sets a value indicating whether the Undo/Redo feature is enabled.

Gets a value indicating whether there is at least one available undo action. This can be used to enable a UI element "Undo".

Gets a value indicating whether there is at least one available redo action. This can be used to enable a UI element "Redo".

The m_context menu.

Gets or sets a value indicating whether to enable the Controls own Context menu

The m_enable auto scrolling.

Gets or sets a value indicating whether or not to enable the ScrollBar below the Plot - default setting: false The Scrollbar simplifies the panning of the plot

Gets or sets a value indicating whether the Panning Scroll Bar should be visible of not

Gets or sets the height of the ScrollBar in pixels

The unselected border color.

Gets or sets the Color of the border when the control is unselected

The m_selected border color.

Gets or sets the Color of the border when the Control is selected

The retention time marker color.

Gets or sets the Color of selected retention time marker

The retention time marker thickness.

Gets or sets the thickness of selected retention time marker

Gets or sets the color of axis grid lines

Gets or sets a value indicating whether larger points are drawn. If set, larger points are drawn (approximately elliptical) for higher intensities. Larger data is drawn first, with small data overlaid. This option makes it easier to see peaks in the density map, at the expense of resolution.

Initializes a new instance of the class. Default constructor

Pan interface

Target percentage to pan Direction to pan - either forward or backwards.

Pan interface

start of pan range end of pan range

Gets or sets a value indicating whether alpha blended lines can be used when creating an Emf file . Default=true

Copy the last drawn plot to the clipboard, with a specified image size

width in pixels height in pixels

Copy the last drawn plot to the clipboard, with a specified image size in real world units

width height Units of size

Copy the last drawn plot to the clipboard, using the same size as on screen

Print Page handler

Rectangle bounds to print graphics to print

Given a rectangle and graphic, draw a map

The bounds in which to draw the map The graphic area on which to draw the map

Clean up any "old" data refs on the undo stacks

did my map need new data?

The raise graph region selected event.

The start. The end.

The raise graph region selected event.

The start. The end.

The initialize scroll bar.

The plot scroll bar_ scroll.

The sender. The e.

The update plot scroll bar.

The range.

Raise Control Selection Event

The on control selected.

The e.

EventHandler for catching, when Graph Scaling has been reset

The on reset scaling.

The e.

Graph Region Selected Event handler

The on graph region selected.

The e.

Control-Scrolled EventHandler. Triggered when scroll bar is moved

On control scrolled. Called when the scroll bar has moved.

The event args. New X data limits.

Handle events for mouse moving over a plot

The on moved over graph.

The e.

The map_ data prepared.

The sender. The event arguments.

Handle a range selection on the Graph

Object that raised the Event Arguments passed through the Event

Move the retention time marker to a new (single) position. Currently: Map only supports a single time marker This is a method rather than property, as it matches chromatogram and allows for expansion to an overload with 2 times (such as average range marker) in future.

The new marker position

Gets the position of the retention time marker. Getting this value does not imply that the marker has been shown. Setting this value must be done by calling "UpdateRetentionTimeMarker", as that method sets the time and enables the marker. (Setting the time without enabling the marker is undefined).

Bounding rectangle Graphics to draw to

Handle key going down: 1. up and down arrows expand and reduce vertically; 2. Delete key deletes the image label matching ImageLabelBeingMoved if AllowDeleteImageLabel is true and ImageLabelBeingMoved is not null.

Key pressed

Handle mouse going down on 3D plot

MouseEventArgs

render a fixed position marker.

The line draw (shape of te marker) The color.

The render pick marker.

The line draw. The color.

The clear adorner.

The get background mask.

The shape.

Get a color, which will be distinguished from the background (inverted)

a color "inverted" with the background.

The mouse moved position.

Set when custom reversible line (adorner) is shown.

Handle mouse movement over 3d plot

mouse position

Gets or sets a value Used to set the control size.

The actual height.

Measures the child elements of a in anticipation of arranging them during the pass.

A that represents the size that is required to arrange child content. An upper limit that should not be exceeded.

Repaint the 3D plot

Where the drawing is rendered

Create a cross hair.

Handle mouse going up on 3D plot

Mouse position

The reset region.

Add header

Where to add the header Text block representing the header Flag indicating whether to draw to the top Flag indicating whether to draw to the bottom.

Handle keyboard input

Event Arguments

Expand vertical - Expand the MassRange by factor of 2

true if graph is changed

contract horizontal scale by a factor

true if graph is changed

reset the scrollbar (full X range).

Expand horizontal

true if graph is changed

contract vertical scale

True if graph was changed

Reset the scaling to the data max values

Public Flag whether Control is actively selected

become selected or not

Determines if this plot should have it's border showing the selected or unselected color.

Handles toggling of ControlSelection

Object that raised the event EventArgs for this Event (Selected, ControlId)

pan enabled.

The adorner for the cursor which tracks the mouse

The adorner used for a fixed position (current scan) marker

Gets or sets a value indicating whether panning has been enabled

The _use custom copy.

Gets or sets a value indicating whether to use a custom copy size and resolution for copy to clipboard"

Gets or sets the width in SizeUnits (as set by CopyUnits) for custom copy feature"

The custom copy width.

The custom copy height.

Gets or sets a Height in SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the Height SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the units of custom copy size"

Gets or sets the clipboard copy format.

Enable or disable panning mode

Save the current Map plot in the UnDo Stack

Sets the Plot back to the last state before the last Do was called - Undoes changes

Sets the plot back into the state before an Undo was called (if there is one) - Redoes Undoes

Clear both UnDo and Redo Stacks

The apply undo redo.

The plot.

The readapt control settings.

show scroll bar if needed. It is not needed if the plot has become full range

The plot base.

The reset scaling tool strip menu item_ click.

The sender. The e.

The copy to clipboard tool strip menu item_ click.

The sender. The e.

The undo zoom tool strip menu item_ click.

The sender. The e.

The redo zoom tool strip menu item_ click.

The sender. The e.

convert boolean "visible" to visibility type.

Is control visible? Converted type

get menu item from context menu.

The context menu. The menu item name. The menu item with the name supplied

The map context menu strip_ opened.

The sender. The e.

Scrol to a new X range

new start of range new end of range

InitializeComponent

Class to add "Rubber band" overlay features to plots, used when mouse is moved or dragged on a plot. The class can show a preview of an object being dragged and dropped (such as a peak label).

Interface to render an object on a device

Render the drawing on the device

The drawing context. number of pixels per device independent pixel

One shape (Geometry) to draw, plus it's color.

Gets or sets Geometry.

Gets or sets Color for pen (outline).

Gets or sets Color for brush (fill).

Draw this drawing

The drawing context. number of pixels per device independent pixel

One shape (Geometry) to draw, plus it's color.

Gets or sets Geometry.

Gets or sets Color for brush (fill).

Draw this drawing

The drawing context. number of pixels per device independent pixel

One shape (Image) to draw, plus it's location.

Gets or sets Image.

Gets or sets Location.

Draw this drawing

The drawing context. number of pixels per device independent pixel

List of things to draw, as part of this adorner

Initializes a new instance of the class.

The adorned element.

Internal initialzation (all constructors)

Initializes a new instance of the class.

The adorned element. The shape to draw. The adorner color. Line thickness, default 0 (thin)

Make a semi transparent version of a color, which also stands out against the background

color to work from Control background semi-transparent version of color

Initializes a new instance of the class.

The adorned element. The shape to draw. The outline color. thickness of the outline The fill color

Add an image to the adorner

The image. The location.

Adds a drawing (a geometry object) to the adorner.

The geometry to add. The color for this geometry fill The color for this geometry outline.

When overridden in a derived class, participates in rendering operations that are directed by the layout system. The rendering instructions for this element are not used directly when this method is invoked, and are instead preserved for later asynchronous use by layout and drawing.

The drawing instructions for a specific element. This context is provided to the layout system.

A control class for plotting and accessing the Calibration Curve.

WpfCalibrationCurvePlotControl

Initializes a new instance of the class. Default constructor

Raise Control Selection Event

Graph-Annotated EventHandler

Graph Region Selected Event handler

EventHandler for catching, when Graph Scaling has been reset

Handle events for mouse moving over a plot

Control-Scrolled EventHandler. Triggered when scroll bar is moved

On control scrolled. Called when the scroll bar has moved.

The event args. New X data limits.

Handle events for click on a symbol

Gets a value indicating whether Control is actively selected

Gets or sets the color of axis grid lines

Gets or sets the color of axis grid lines, going through 0,0 Only used when is set.

Gets or sets the thickness of axis grid lines, going through 0,0 Only used when is set.

Gets or sets a value indicating whether axis grid lines are enhanced at zero.

Gets or sets the color of axis line

Gets or sets the thickness of axis line. Default 0, a thin line.

Gets or sets the color of axis name

Gets or sets the color of axis numeric values or category labels. This is the color for the text drawn by the major tick marks.

Gets or sets the color for gradient fill of the background

Gets or sets a value indicating whether gradient fill the background

Gets or sets the direction of gradient fill for the background

Gets the plotting object for the calibration curve.

The control dimensions.

Gets or sets the control size.

Gets or sets the clipboard copy format.

Gets a translator, used to translate mouse position to data position

Gets or sets a value indicating whether or not the default GraphRegionSelectionEvent is automatically handled or not - registers and deregisters the default method for Event Handling of GraphRegionSelection

Gets or sets a value indicating whether or not to enable the ScrollBar below the Plot - default setting: false The Scrollbar simplifies the panning of the plot

Gets or sets a value indicating whether the Controls has it's own Context menu

Gets or sets a value indicating whether the Undo/Redo feature is enabled

Gets a value indicating whether there is at least one available undo action. This can be used to enable a UI element "Undo".

Gets a value indicating whether there is at least one available redo action. This can be used to enable a UI element "Redo".

Gets or sets the color used for labels (prefixes) in the plot heading

Gets or sets a value indicating whether the Y-Axis is shown with an exponential scale

Gets or sets the color of fitted curve trace

Gets or sets the thickness of fitted curve trace. The default (0) gives a thin line.

Gets or sets the face name of font

Gets or sets the color used for values in the plot heading

Gets or sets the color used for labels in the plot heading

Gets or sets the color used for values in the plot heading

Gets or sets the control's Id

Gets or sets the color used for labels (prefixes) in the plot heading

Gets or sets the color of calculated amount marker line

Gets or sets the thickness of calculated amount marker line. The default (0) gives a thin line.

Gets or sets the maximum font size (inch)

Gets or sets the minimum font size (inch)

Gets or sets a value indicating whether panning has been enabled

Gets or sets a value indicating whether the plot is prepared to receive annotations

Gets or sets the color used for labels (prefixes) in the plot heading

Gets or sets the color of the border when the control is selected

Gets or sets a value indicating whether to paint the border round the CalibrationCurve Plot

Gets or sets the Size of all symbols. Use this property if all symbols should be a uniform size. Specific sizes may be set for each symbol, for example by calling IncludedSymbolSize

Gets or sets the color of the border when control is unselected

Gets or sets the cursor pick

Gets or sets Annotation manager to manage Plot annotations

Gets or sets the Header Manager to manage header data for the plot

This method can be used to add annotations manually

Attribute with parameters for the Annotation Settings Low: position to point to ; High: position for label Low: intensity to point to; High intensity for label Id of the selected Trace

Clear all Headers from the plot

Clear both UnDo and Redo Stacks

Gets or sets a value indicating whether alpha blended lines can be used when creating an Emf file . Default=true

Copy the last drawn plot to the clipboard, with a specified image size

width in pixels height in pixels

Copy the last drawn plot to the clipboard, with a specified image size in real world units

width height Units of size

Copy the last drawn plot to the clipboard, using the same size as on screen

Attach data to a calibration curve, based on quantitation results. Attaches included, excluded, line of fit and headings.

XY points for plotting, generated from inputs to and output of the regression fit Units of concentration Name of the compound Algorithm used for regression fit Weighting used for regression fit True if peak area was used (else height) True if this is a ratio (to internal standard) RSD to show in second line of heading (for ISTD plots)

Attach data to a calibration curve, based on quantitation results. Attaches included, excluded, line of fit and headings.

Save the current Chromatogram Plot in the UnDo Stack

Given a rectangle and graphic, draw a Calibration Curve

The bounds in which to draw the Calibration Curve The graphic area on which to draw the Calibration Curve

Check if this point intersects either the included or excluded trace

Point to test true if a point was found

Save this plot as an EMF format file.

file to create If set, output may contain alpha blended (transparent) lines

Pan interface

Target percentage to pan Direction to pan - either forward or backwards.

Pan interface

start of pan range end of pan range

Sets the plot back into the state before an Undo was called (if there is one) - Redoes Undoes

Remove any calculated amount markers from the plot

Reset the scaling to the data max values

Set the marker for highlighting the point on the curve used for a given component

X position (amount) Y position (response ratio)

Add header

Where to add the header Text block representing the header Flag indicating whether to draw to the top. This flag is only used for left and right positions. For example: If a plot has a "top" heading, it will normally span the full width of the plot, and a heading set "left" will start below the "top" heading. If "toTop" is set when attaching the "left" heading, then the "left" heading extends to the top of the plot area, and the "top" heading is therefore indented by the size of the "left" heading Flag indicating whether to draw to the bottom. flag is only used for left and right positions. For example: If a plot has a "bottom" heading, it will normally span the full width of the plot, and a heading set "left" will start above the "bottom" heading. If "toBottom" is set when attaching the "left" heading, then the "left" heading extends to the bottom of the plot area, and the "bottom" heading is therefore indented by the size of the "left" heading

Handles toggling of ControlSelection

Object that raised the event EventArgs for this Event (Selected, ControlId)

Pan interface to enable/disable pan by drag

Sets the Plot back to the last state before the last Do was called - Undoes changes

Apply new annotation settings (OK or Apply on an annotation form). This method sets the mouse mode ready for dropping annotation onto the plot. The next mouse click or drag will be used to place an annotation.

Description on the annotation

Expand horizontal

true if graph is changed

Expand vertical scale (zoom in)

true if graph is changed

contract horizontal scale by a factor

true if graph is changed

reset the scrollbar (full X range).

zoom out in y: contract vertical scale

True if graph was changed

Attach data to a calibration curve, based on quantitation results. Attaches included, excluded, line of fit and headings.

XY points for plotting, generated from inputs to and output of the regression fit Units of concentration Name of the compound Algorithm used for regression fit Weighting used for regression fit True if peak area was used (else height) True if this is a ratio (to internal standard) if true, add an RSD line to the heading SD to show in second line of heading (for ISTD plots)

Given a rectangle and graphic, draw a Calibration Curve

The bounds in which to draw the Calibration Curve The graphic area on which to draw the Calibration Curve

Print Page handler

Rectangle to print graphics to print

Print this plot

Bounding rectangle Graphics to draw to

Create example data for design mode

Measures the child elements of a in anticipation of arranging them during the pass.

A that represents the size that is required to arrange child content. An upper limit that should not be exceeded.

Invoked when an unhandled attached event is raised on this element. Implement this method to add class handling for this event.

The that contains the event data.

Invoked when an unhandled routed event is raised on this element. Implement this method to add class handling for this event.

The that contains the event data. The event data reports that the left mouse button was pressed.

Invoked when an unhandled routed event reaches an element in its route that is derived from this class. Implement this method to add class handling for this event.

The that contains the event data. The event data reports that the left mouse button was released.

Invoked when an unhandled attached event reaches an element in its route that is derived from this class. Implement this method to add class handling for this event.

The that contains the event data.

Draws the content of a object during the render pass of a element.

The object to draw.

Translate from data format returned by regression into format needed by symbol trace

Data from regression Data ready to plot

Add equation items to the heading.

The heading.

apply changes to the plot from the undo or redo stack.

The plot.

Start an adorner, which shows the region being zoomed by a line or box being dragged over a plot.

The mouse down point.

The calibration curve context menu strip opened.

The sender. The event.

Remove any adorner I have created

The control's adorner layer

End of activity of "cursor pick" (mouse went up)

The copy to clipboard tool strip menu item was clicked.

The sender. The event.

Create cross hair cursor.

Construct the adorner

The region where the mouse was clicked. The style of the pick marker. The mouse down point.

Create example heading for designer mode

The heading.

Design the plot heading.

The calibration curve data. The component name. The regression method. The weighting. True if heading should show RSD. The RSD value.

permits heading to be recolored etc before plot

The heading.

Add RSD values to heading

The heading.

Create a color which shows up against the background

The background color.

Determine the correct color for the adorner

The path of the adorner. The color to use.

Calculate a color which will show up against the background of the plot.

The color to use (for an adorner)

get the display rectangle

Size of the plot

handle annotation.

The start. The end.

Update the x scale, due to a zoom in x.

The range zoomed true if the plot range was updated

handle y axis zoom.

The range. The .

Initialize the scroll bar.

Perform actions on control selected.

The event.

The on graph annotation changed.

The event.

On graph region selected.

The event.

on moved over graph.

The e.

on reset scaling.

The event.

on symbol click.

The e.

The paint for mouse move action.

The plot scroll bar has scrolled.

The sender. The e.

raise the graph region selected event.

The start of the selected region. The end of the selected region.

this is the default method that is triggered when a GraphRegion is selected

Object that raised the Event Arguments that are passed through the event - (Range of selected region in Pixels and DataValues)

Fix up control X range and scroll bar.

The redo tool strip menu item was clicked.

The sender. The event.

Render a cursor pick marker.

The shape drawn. The color.

The reset scaling tool strip menu item was clicked.

The sender. The event.

set annotation.

Test if a point is within a symbol

The point clicked.

The undo tool strip menu item was clicked.

The sender. The event.

Update plot scroll bar range.

The range.

Scrol to a new X range

new start of range new end of range

The label value pair.

Gets or sets the label.

Gets or sets the value.

InitializeComponent

Interaction logic for WpfChromatogramControl.xaml

WpfChromatogramControl

The _undo manager.

The _plot scroll bar support.

The cursor cross hair.

The annotation manager.

The marker manager.

The interactive cross hair.

The envelope.

The peaks.

The cursor input.

The detected peak annotation.

The pending marker.

The header manager.

The trace id for max intensity.

The max intensity.

The min plot time.

The _max plot time.

The intensity scale update.

The _update range scale.

The _plot is selected.

The _amplify clear region.

The _amplify enabled.

The _amplify factor.

The selected (highlighted) trace.

Gets or sets the selected trace.

The _end chosen.

The fixed baseline point time.

The fixed baseline point intensity.

Mask for background.

Is mouse captured?

Is this being run from a unit test?

The chromatogram full range.

The _multi trace style.

Gets or sets a value indicating whether the style of the auto generated heading is for multiple traces. This is set automatically by "CreateChromatogram" calls, based on the number of traces. For multiple traces, the standard heading is one line, containing a file name. For single trace, a second line is added for the filter. For multiple traces "filter" becomes part of the trace title, as it is separate per trace.

Gets or sets a value indicating whether retention Time selections snap to the trace data. When this is set, a single point click within a chromatogram trace returns the time of the nearest scan in that trace. When not set: The exact time picked is returned. Default: true

The _heading file name.

Name for identifying a retention time marker

Gets or sets Id for control

The chromatogram.

Gets or sets the object which draws the chromatogram.

Gets or sets the object used to control peak labeling

display the retention time marker.

Gets or sets a value indicating whether to permit display of the retention time marker. When enabled, the marker will appear on the first mouse selection in the plot, or the first call to . If the marker is disabled, then any existing marker is removed.

The retention time marker retention time. initially no marker on the plot, so set to -1000 minutes

The retention time marker end retention time. initially no marker on the plot, so set to -1000 minutes

Gets or sets the retention time for positioning the marker

Gets a value used to translate screen position to data position.

Gets or sets a value indicating whether the plot should begin adding a manual peak baseline at the next mouse click on the plot

The _enable auto range selection handling.

Gets or sets a value indicating whether or not the default GraphRegionSelectionEvent is automatically handled or not - registers and unregisters the default method for Event Handling of GraphRegionSelection

Gets or sets a value indicating whether the Undo/Redo feature is enabled.

The _enable context menu.

Gets a value indicating whether there is at least one available undo action. This can be used to enable a UI element "Undo".

Gets a value indicating whether there is at least one available redo action. This can be used to enable a UI element "Redo".

The _enable auto scrolling.

Gets or sets a value indicating whether or not to enable the Scrollbar below the Plot - default setting: false The Scrollbar simplifies the panning of the plot

Gets or sets a value indicating whether the Panning Scroll Bar should be visible of not

Gets or sets the height of the automatic Scroll Bar

Gets or sets peaks labels which are added to the chromatogram, intended for annotation of detected peaks. Labels are formatted by the calling code as chromatogram has no knowledge of fields available in the detected peaks. This method is for backwards compatibility for chromatograms with one plot. For multiple plots call once per trace, to add specific annotations keyed to the traces.

Gets or sets the color of automatic peak labeling text

Gets or sets The color of automatic peak labeling joining lines and boxes

Gets or sets the thickness of automatic peak labeling joining lines and boxes. Units 1/100 inch. Default 0 is a thin line.

Gets or sets a value indicating whether smoothing is done on joining lines for automatic peak labels.

Gets or sets a value indicating whether blending is done on joining lines for automatic peak labels.

Gets or sets a value indicating whether smoothing (anti-alias) of connected line style traces is in effect. This affects rendering quality only, and not the shape of the plot.

Gets or sets the color for gradient fill of the background

Gets or sets a value indicating whether to gradient fill the background

Gets or sets the direction of gradient fill for the background

The _use custom copy.

Gets or sets a value indicating whether to use copy size and resolution from context menu"

The custom copy resolution.

Gets or sets the resolution DPI for custom copy feature"

Gets or sets the width in SizeUnits (as set by CopyUnits) for custom copy feature"

The custom copy width.

The custom copy height.

Gets or sets a Height in SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the Height SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the units of custom copy size"

Gets the Region list for peak labels

Remove all detected peak annotations from the list

Add a new annotation item to the list.

Text annotation to be added to the list

The _pick.

Gets or sets the cursor pick

The pending annotation.

Gets or sets a value indicating whether the object is waiting for annotation

Gets or sets the file name for the heading, as initialized by CreateChromatogram... calls.

The heading label color.

Gets or sets the color used for labels (prefixes) in the plot heading

The heading value color.

Gets or sets the color used for values in the plot heading

The heading filter color.

Gets or sets the color used for scan filter in the plot heading

The heading peak name.

Gets or sets the peak name for the heading, as initialized by CreateChromatogram... calls.

The heading filter text.

Gets or sets filter text for the heading, as initialized by CreateChromatogram... calls.

Gets the peaks which have been labeled on this plot

Gets the time range of the chromatogram

Show the scale factor right?

Gets or sets a value indicating whether the scale factor in the plot heading is shown to the right. If not set, it is placed immediately after other heading items.

Gets or sets a value indicating whether to paint the border round the chromatogram Plot

The unselected border color.

Gets or sets Color of border when control is unselected

The retention time marker color.

Gets or sets the Color of selected retention time marker

The retention time marker thickness.

Gets or sets the thickness of selected retention time marker

The _selected border color.

Gets or sets color of border when control is selected

Gets or sets color of axis line

Gets or sets a value which defines how to handle a Y scale, which has no range. By default, the scale is expanded to include 0. For example: in MinMax automatic scaling, with 10 data values all at Y value -66, there is no logical auto scale range, so the range becomes from "-66 to 0". Alternatives would include expanding the scale, to put "-66' at the mid point.

Gets or sets the color of axis grid lines

Gets or sets the color of axis grid lines, going through 0,0 Only used when is set.

Gets or sets the thickness of axis grid lines, going through 0,0 Only used when is set.

Gets or sets a value indicating whether axis grid lines are enhanced at zero. This is sometimes desirable when plots can contain both positive and negative signals. Note that a grid line will not be drawn "on top of" an axis ruler line. So: with a Y axis which begins at "intensity=0" the zero grid line is not drawn.

Gets or sets the thickness of axis line. Default 0, a thin line.

Gets or sets the color of axis name

Gets or sets the color of axis numeric values or category labels. This is the color for the text drawn by the major tick marks.

Gets or sets the color of lines showing amplified regions.

Gets or sets the color of scale factor text above amplified regions.

Gets or sets the percent of highlighting of selected trace. Suggested values are 0 for no highlight and between 8 and 15 for visible highlights. Higher values can be used for emphasis (such as a slide show), but may make an interactive display harder to read.

Gets or sets line drawing style

Gets or sets a value indicating whether to overlay chromatogram traces

Gets or sets the skew angle for overlaid traces

Gets or sets the elevation for overlaid traces

Gets or sets a value indicating whether to draw Backdrop in overlaid traces

Gets or sets a value indicating whether to rotate peak label text

Gets or sets a value indicating whether to box peak label text

Gets or sets the Threshold (%) for peak labels

Gets or sets the maximum label offset

Gets or sets a value indicating whether label is permitted to be offset

Gets or sets a value indicating whether X axis is offset from data

Gets or sets a value indicating whether Y axis is offset from data

Gets or sets a value indicating whether X axis is split, into several equal sub ranges

Gets or sets the number of divisions (splits) on the X-Axis

Gets or sets a value indicating whether the Y-Axis is shown with a percentage scale

Gets or sets a value indicating whether the Y-Axis is shown with an exponential scale

Gets or sets the X-Axis name

Gets or sets the name to show on Y Axis

Gets or sets the method of auto scaling

Gets or sets a value indicating whether to Fix scaling to application provided value

Gets or sets the fixed scaling value (100%), when is set

Gets or sets the method of automatic normalization

Gets or sets the minimum Y value, as a % of base value

Gets or sets the maximum Y value, as a % of base value

Gets or sets a value indicating whether to apply same scaling to all overlaid or stacked plots

Gets or sets a value indicating whether to add peak labels to apex of signals in plot, showing Retention Time

Gets or sets the Retention Time label format (minutes, seconds)

Gets or sets a value indicating whether to add peak labels to apex of signals in plot, showing Scan Number

Gets or sets a value indicating whether to add peak labels to apex of signals in plot, showing the Base Peak Mass

Gets or sets the peakLabel precision

Gets or sets the table of colors for traces. Colors are cycled for larger numbers of traces

Gets or sets table of thickness for traces. Thicknesses are cycled for larger numbers of traces

Gets or sets a table of Dash Style for traces. Dash Styles are cycled for larger numbers of traces

Initializes a new instance of the class. Default constructor

convert boolean "visible" to visibility type.

Is control visible? Converted type

Get a color, which will be distinguished from the background (inverted)

a color "inverted" with the background.

Create demo data for use in "designer" mode

Invoked when an unhandled attached event is raised on this element. Implement this method to add class handling for this event.

The that contains the event data.

The _mouse left down point.

The _cursor style.

Invoked when an unhandled routed event is raised on this element. Implement this method to add class handling for this event.

The that contains the event data. The event data reports that the left mouse button was pressed.

Test if a selectable marker has been selected, and if so, start the drag

True, if drag started

Find which selection region best matches a point. Ideally: The user is working in one trace (the selected trace). This can be complicated by overlapping traces. Where the section is still within the inner (data) region of the selected trace, return that. Continue down alternatives, until something acceptable is found.

The point to test The region found, or null

Test if a draggable marker has been selected, and if so, start the drag

True, if drag started

The mouse moved position.

Set when custom reversible line (adorner) is shown.

Invoked when an unhandled attached event reaches an element in its route that is derived from this class. Implement this method to add class handling for this event.

The that contains the event data.

Highlight a peak label, which can be selected

Create peak highlight.

The start region (where the mouse was moved)

Invoked when an unhandled routed event reaches an element in its route that is derived from this class. Implement this method to add class handling for this event.

The that contains the event data. The event data reports that the left mouse button was released.

Draws the content of a object during the render pass of a element.

The object to draw.

get the display rectangle

Size of the plot

Measures the child elements of a in anticipation of arranging them during the pass.

A that represents the size that is required to arrange child content. An upper limit that should not be exceeded.

Initialize the chromatogram. This performs the following actions: Markers are cleared (Chromatogram.ClearMarkers();) any "PPD peak envelope" data is cleared (ClearEnvelopes) any "detected peak" annotation is cleared (ClearDetectedPeakAnnotation) Any cursor translation data is cleared (mouse position to data x/y mapping) CursorTranslator.Clear(); All traces are removed (RemoveAllTraces) Scaling is reset (ResetScaling).

Remove PPD envelope markers.

This method completes setup of a new chromatogram, after all traces have been added by the calling application. It is called internally from within various "CreateChromatogram..." helper methods For example: This method clears the range expansion "undo" list, by calling ClearUndoRedo.

The font family name.

Gets or sets the face name of font

The _maximum font size.

Gets or sets the maximum font size (inch)

The _minimum font size.

Gets or sets the minimum font size (inch)

Gets or sets the clipboard copy format.

Gets or sets the control size.

Gets or sets the number of Decimal places to show.

Gets or sets the number of Decimal places to for base peak. Setting this property creates a single value, used for all traces. Use "BasePeakDecimalsPerTrace" to set this separately per trace.

Gets or sets a value indicating whether Aliasing is used. Aliasing creates "jagged" lines, but may avoid any gray appearance on thin lines. Due to improvements in .net 4.0, this is most likely not needed, and default to false.

Read data from a raw file over a given time range, Smooth the signal. Integrate the signal, and create as a single trace chromatogram plot, with a heading showing the filter The method selects the appropriate instrument from the raw file, and leaves this selected on exit.

Already opened raw file to read from Lowest time requested for chromatogram Highest time requested for chromatogram Definition of chromatogram (scan filter, mass ranges etc.) Name to show in title (may be empty) Integrator is used to detect peaks in the file. Maybe be null, or "new Integrator()" if no integration is required Smoothing options The peaks found by the integrator

Adds data from a component, which has already been peak detected, to a chromatogram plot.

Data for the trace (the chromatogram) The usable range of the data The peak detected for this component The raw file name, for display in the heading The name of the component Text to display in the heading as "scan filter"

Adds data from a component, which has already been peak detected, to a chromatogram plot.

Adds data from a list of components, which have already been peak detected, to a chromatogram plot. This calls the following public methods and properties: InitializeChromatogram(); MultiTraceStyle = true

Data for the trace (the chromatogram) The usable range of the data The peaks detected for this component The raw file name, for display in the heading Title string which are placed above each trace. This area holds one (long) line of text. For example: the name of the component Text to display to the right of each traces, for example "scan filter". This text is shown after the scaling factor for the trace, and is word wrapped into multiple lines If this is true, titles are shown above each trace, based on "". If false, no space is reserved for titles above traces Sample the Gaussian about this times as fast as the chromatographic sampling, to make smooth peaks.

Construct a chromatogram from data for a set of traces

The data for each trace. This also includes a number of trace labeling and styling options. The usable range of the data The raw file name, for display in the heading If this is true, titles are shown above each trace. If false, no space is reserved for titles above traces Determines if titles are to be shown to the right of each trace. Set this false, and all titles to "string.empty" if not needed Determines if the normalization values should be shown to the right of each trace If neither of showRightTitles or showScalingRight is set, then this sets how much white space is reserved to the right. This affects the style of the built in heading only (default true). when set to multi trace style, the default heading has only 1 line. When this is false, it has two lines, including the scale factor in the heading. If peaks have an envelope, Sample the Gaussian about this times as fast as the chromatographic sampling, to make smooth peaks.

Adds data from a list of components, which have already been peak detected, to a chromatogram plot.

Adds data from a component, which has already been peak detected, to a chromatogram plot.

Data for the trace (the chromatogram) The usable range of the data The peaks detected for this component The raw file name, for display in the heading The name of the component Text to display in the heading as "scan filter" Sample the Gaussian about this times as fast as the chromatographic sampling, to make smooth peaks.

Method to add one or more traces to the chromatogram

total number of traces added so far (updated by the number of plots added). Calling code should initialize this to zero before the first call Time data, first index is trace, second is set of values per trace Intensity data, first index is trace, second is set of values per trace Scan numbers, which may be used to annotate each peak apex Base peak masses, which may be used to annotate each peak apex the number of traces, after this one has been added

Method to add one or more traces to the chromatogram

Time data, first index is trace, second is set of values per trace Intensity data, first index is trace, second is set of values per trace Scan numbers, which may be used to annotate each peak apex Number of chromatograms to add total number of traces added so far (updated by the number of plots added). Calling code should initialize this to zero before the first call

Method to add one or more traces to the chromatogram

Time data, first index is trace, second is set of values per trace Intensity data, first index is trace, second is set of values per trace Scan numbers, which may be used to annotate each peak apex Base peak masses, which may be used to annotate each peak apex Number of chromatograms to add total number of traces added so far (updated by the number of plots added). Calling code should initialize this to zero before the first call

Method to add one or more traces to the chromatogram

Time data, first index is trace, second is set of values per trace Intensity data, first index is trace, second is set of values per trace Number of chromatograms to add total number of traces (updated by the number of plots added)

Adds data from a list of components, which have already been peak detected, to a chromatogram plot.

Data for the traces (the chromatograms) The usable range of the data The peaks detected for this component The raw file name, for display in the heading Title string which are placed above each trace. This area holds one (long) line of text. For example: the name of the component Text to display to the right of each traces, for example "scan filter". This text is shown after the scaling factor for the trace, and is word wrapped into multiple lines If this is true, titles are shown above each trace, based on "". If false, no space is reserved for titles above traces

Adds data from a list of components, which have already been peak detected, to a chromatogram plot.

Remove all current plots

Add header

Clears all headers from the Chromatogram Plot

Pan interface

Target percentage to pan Direction to pan - either forward or backwards.

Pan interface. Pan assumes that the scale between start and end is unchanged

start of pan range end of pan range

Draw the chromatogram in the indicated rectangle

Rectangle to draw in Where to draw

Given a rectangle and graphic, draw a chromatogram

The bounds in which to draw the chromatogram The graphic area on which to draw the chromatogram

Gets or sets a value indicating whether alpha blended lines can be used when creating an Emf file . Default=true

Copy the last drawn plot to the clipboard, with a specified image size and units

width in supplied units height in suppled units Units of width and height

Copy the last drawn plot to the clipboard, with a specified image size

width in pixels height in pixels

Copy the last drawn plot to the clipboard, using the same size as on screen

Apply new amplification settings (OK or Apply on an amplify form, toolbar action etc.). This method sets the mouse mode ready for adding or removing amplifiers on the plot. The next mouse click or drag will be used to place or remove the amplifier.

Description of change needed to amplifiers

Description on the annotation

This method can be used to add annotations manually

Attribute with parameters for the Annotation Settings Low: position to point to; High: position for the PeakLabel Low: intensity to point to; High intensity for the PeakLabel Id of the selected Trace

Description on the annotation

Gets the collection of markers on the current plot

Replace the collection of markers with a new set. All previous markers will be removed from the object, and the attached plot. The new markers will be attached to the plot.

New set of markers

Gets the collection of text label sets on the current plot. Note: each added label is created as a "set of labels" containing a single label.

Replace the collection of text annotations with a new set. All previous text annotations will be removed from the object, and the attached plot. The new text annotations will be attached to the plot.

New set of annotations

Move the retention time marker to a new position. When the marker is enabled, using the "" property, either a mouse click has to be made on the chromatogram, or this must be called at least once, for a marker to appear.

The new marker position

The new marker start position The new marker end position Height of marker as a % of plot vertical scale. Default 50%

Print Page

Rectangle to print Graphics to print

Hit test for the Chromatogram trace

point to test for Cursor Region to test a CursorCrosshair Style

See if the cursor overlaps a label area

Point to test Region found or null if no region found

Test to check if a peak is hit

point to test for Region within which to test Point to be filled with the start point True if the right end of the marker has been picked Time of the fixed end of the peak baseline (the end not being dragged) Intensity of the fixed end of the peak baseline (the end not being dragged) PeaksPointArray object

Test to check if a peak baseline end marker is hit

Change "select" attribute for plot

become selected or not

Determines if this plot should have it's border showing the selected or unselected color.

Print a page.

Bounding rectangle Graphics to draw to

Manual add peak is completing. Creates an event with the start and end of the baseline.

The start. The end.

The manual peak pick has completed.

The start of the picked region. The end of the picked region.

Create the manual baseline args.

The point at right. The cursor end region. The end. Event args for a manual baseline selection

Handle key down: up and down arrows expand and reduce vertically

Key pressed

Handle whether to delete of image label being dragged/clicked when Delete key is hit.

Key pressed

Handles a range selection on the Graph

Object that sent the Event Arguments passed through the event (Range in Pixels and Data Values)

Horizontal line pick.

The event. The start. The end.

Handle events for retention time being selected from a plot

The on retention time selected.

The e.

Handle events for mouse moving over a plot

The on moved over graph.

The e.

Handle events for Manual Baseline being selected

On manual baseline selected.

The event args.

Handle events for Manual peak being added

On manual peak added.

The event args.

EventHandler for catching, when Graph Scaling has been reset

The on reset scaling.

The event args.

Graph Region Selected Event handler

Label double click Event handler (for selectable annotations only)

The on graph region selected.

The e.

The label was clicked twice.

The e.

Trace Selected Event handler. Called when the selected trace number is changed. For example: when clicking on a trace title.

Action on Trace selected.

The event data (trace number which was selected).

Y axis scale selected. Register for this event to capture a mouse zoom, which would update the Y scaling. Set "e.Handled" to prevent the default action (Y scale change).

On y scale expanded.

The event args.

X axis scale selected. Register for this event to capture a mouse zoom, which would update the X scaling. Set "e.Handled" to prevent the default action (X scale change).

On x scale expanded.

The event args.

Control-Panned EventHandler

On control panned.

The event args.

Control-Scrolled EventHandler. Triggered when scroll bar is moved

On control scrolled. Called when the scroll bar has moved.

The event args. New X data limits.

Graph-Amplified EventHandler

On graph amplified.

The event args.

Graph-Annotated EventHandler

On graph annotation changed.

The event args

Raise Control Selection Event

On control selected.

The event args.

The property changed.

On property changed.

The event args.

Gets a value indicating whether the Control is actively selected

Handles toggling of ControlSelection

Object that raised the event EventArgs for this Event (Selected, ControlId)

Scrol to a new X range

new start of range new end of range

Expand vertical

true if graph is changed

contract horizontal scale by a factor

true if graph is changed

show scroll bar if needed. It is not needed if the plot has become full range

The plot base.

Expand horizontal

true if graph is changed

contract vertical.

The factor. true if scale has changed

Show all data (vertical). Expansion of "Contract vertical" to return to full scale

true if scale has changed

Gets a value indicating whether I should expand and contract all plots.

expand vertical.

The factor. true if scale has changed

contract vertical scale

True if graph was changed

Reset the scaling to the data max values

reset the scrollbar (full X range).

The _pan enabled.

This private filed is set automatically to begin display of retention time markers Markers are disabled by default. If DisplayRetentionTimeMarker is set, the they become enabled ion the first mouse click on the plot or on a call to UpdateRetentionTimeMarker

Gets or sets the ImageLabel being dragged and dropped

Gets or sets a value indicating whether to allow auto deletion of dragged/clicked ImageLabel when Delete key is hit.

The cursor pan lock time.

Gets or sets a value indicating whether panning has been enabled

Enable or disable panning mode

Initialize the scroll bar.

The plot scroll bar_ has scrolled.

The sender. The event args.

Update plot scroll bar.

The range.

The reset scaling tool strip menu item was clicked.

The sender. The event args.

The redo tool strip menu item was clicked.

The sender. The event args.

The undo tool strip menu item was clicked.

The sender. The event args.

The chromatogram context menu strip was opened.

The sender. The event args.

chromatogram context menu strip is opening. Enable/disable menu items.

The sender. The event args.

Configure an undo redo feature.

The menu item to configure (show or hide). Set if undo/redo is enabled.

get menu item from context menu.

The context menu. The menu item name. The menu item with the name supplied

copy to clipboard tool strip menu item clicked. Perform copy.

The sender. The event args.

Save the current ChromatogramPlot in the UnDo Stack

Sets the Plot back to the last state before the last Do was called - Undoes changes

Sets the plot back into the state before an Undo was called (if there is one) - Redoes Undoes

Clear both UnDo and Redo Stacks

Apply undo redo.

The plot.

Modify control (range) settings.

Create the trace array.

The trace signal. The data for the trace.

Add chromatogram traces. This is called internally by various "CreateChromatogram..." format helper methods. Call it externally to obtain greater control of the format. When calling this externally, you should call InitializeChromatogram(); first, to clear previous data (or perform other initialize steps as needed). Then call this method. Then configure the plot heading, as needed, and finally call the following method: DataUpdateComplete();

The titles for each trace (optional, may be null). For example "scan filter for this chromatogram". The compound names for each trace. Optional, may be null. The signals. The number of chromatograms to add. (less than or equal to the number of supplied signals). The peaks. The trace counter. This is typically initialized as int traceCounter=0. However, when appending traces, it should be set to the count of previously added traces. Determines if titles should be shown above traces. The over sample.

Append the detected peaks for one trace to the collection.

The over sampling factor to make smooth envelopes. The peak collection. The trace signal. The trace. The .

Gets or sets a value indicating whether to hide auto labels when peaks are detected. In this mode, if there is at least one detected peak for a specific trace, "peak apex label" requests, such as "label apex with RT" are suppressed for that individual trace. Traces which have no detected peaks still get "auto labels" for RT, provided that these are requested.

Test if a peak has an envelope.

The peak. True if the peak has a fitted peak envelope.

Create a peak envelope shape.

The peak. The signal. The n peak number. The trace. The over sampling rate.

Construct a heading.

The standard heading.

The block.

The create heading.

The heading. The file name with path. The name. The filter text.

Add a counted trace.

The trace counter. The max intensity. The trace points. The trace counter (incremented).

The add retention time marker.

Handle amplify.

The start. The end.

handle x axis zoom.

The event args. true if zoomed.

handle y axis zoom.

The event. True if zoomed.

Handle y axis zoom.

The absolute range range. Trace where this range was taken from True if zoomed

Handle retention time update.

The start.

Handle trace selection.

The start.

Update selected trace.

The trace id.

Handle retention time update.

The retention time. The trace id.

Handle annotation.

The start. The end.

Handle graphic marker.

The start. The end.

Set annotation.

Attach markers (custom graphics) to the spectrum plot.

Update retention time (of the marker).

The start time of the marker. The end time of the marker. The height.

Raise the trace selected event.

Trace number of trace which was selected

Raise graph region selected event.

The start. The end.

Find the inner region of the selected trace, provided: 1: the supplied points are in that region. 1: the region has x/y ranges.

Start point of selection End point of selection The region of the selected trace, or null if no trace matches the rules

Find the outer region of the selected trace, provided: 1: the supplied points are in that region. 1: the region has x/y ranges.

Start point of selection End point of selection The region of the selected trace, or null if no trace matches the rules

Adorner actions for mouse down.

Create color and thickness of adorner

Describes the adorner A Tuple of line color, fill color, thickness

The adorner.

Gets or sets the line tickness of the pick marker. This is any marker created after the left button is held down and dragged. Default 0: thin line

The control dimensions.

render the pick marker.

The shape. The color.

Render the pick marker.

The shape to draw. The color, as "line color, fill color, thickness"

Get a background mask.

The lines to draw. The color to use.

Clear the adorner.

the adorner layer

Move the rubber band.

Perform panning.

Create a cross hair.

Handle pick complete.

true if the adorner layer must be cleared. When an object is selectable, then it may remained as selected, and not cleared.

Initialize values from test case.

The details. The x. The y.

Inject the interface which provides peak labels

Interface to provide peak labels

Add annotation for detected peaks

The annotation to add

Gets the base class of this

The batch summer.

Method executed in parallel

Initializes a new instance of the class.

The trace points. The start. The batch end. The chromatogram intensities. The chromatogram times. The scans. The base peak masses.

Execute internal (makes locals out of fields).

The start. The batch e end. The trace points. The chromatogram intensities. The chromatogram times. The scans. The base peak masses.

Save this plot as an EMF format file.

file to create. If set, output may contain alpha blended (transparent) lines

InitializeComponent

Which end of the baseline is selected

Left end is selected

Right end is selected

The scale update.

Gets or sets a value indicating whether a scale update pending?

Gets or sets the new range to apply

Determine what happened with the mouse

Mouse has Moved

Mouse Left Button has gone Up

Mouse Left Button has gone Down

a Mouse button has gone Down

Interaction logic for WpfSpectrumPlotControl.xaml

WpfSpectrumPlotControl

The cursor cross hair.

The envelope.

The heading.

The interactive cross hair.

The marker manager. This holds information about a pending marker. (shape, color etc.)

The peaks.

The plot scroll bar support.

The undo manager.

The _adorner.

The amplify clear region.

Test if The amplifier is enabled.

The amplify factor.

The backup.

The control dimensions.

The _cursor pan lock mass.

The _cursor pick start point.

The _custom copy height.

The custom copy width.

The _enable auto range selection handling.

The m_enable auto scrolling.

The m_enable context menu.

Gets or sets the font family name.

The filter text to show in the heading

The _heading filter color.

The heading label color.

The _heading path.

The scan number to show in the heading

The scan time to show in the heading.

The _heading value color.

The intensity scale update.

is the mouse captured.

is a test case?

The maximum font size.

Maximum mass in data - maximum x value.

The _minimum font size.

Minimum mass in data - min x value.

The mouse left down point.

The mouse moved position.

The _pan enabled.

This is set when the next mouse action is related to adding markers.

test if plot is selected.

The _m selected border color.

Test if this is the selected trace.

The _spectrum plot control.

The unselected border color.

The _use custom copy.

Initializes a new instance of the class. Control for plotting spectra

define a general delegate form to convert a graphics "Scan" object to a Graphics scan, which can be rendered. This allows an application to completely customize what data from the instrument scan is plotted.

Scan to convert The converted scan

Control-Panned EventHandler

Raise Control Selection Event

Graph-Amplified EventHandler

Graph-Annotated EventHandler

Graph Region Selected Event handler

Label double click Event handler (for selectable annotations only)

EventHandler for catching, when Graph Scaling has been reset

Handle events for retention time being selected from a plot

The property changed.

Gets a value indicating whether the Control is actively selected

Gets or sets a value indicating whether to allow auto deletion of dragged/clicked ImageLabel when Delete key is hit.

Gets or sets the color of lines showing amplified regions.

Gets or sets the color of scale factor text above amplified regions.

Gets or sets a value indicating whether blending is done on joining lines for automatic peak labels.

Gets or sets a value indicating whether smoothing of joining lines for automatic peak labels.

Gets or sets the color of automatic peak labeling joining lines and boxes

Gets or sets the thickness of automatic peak labeling joining lines and boxes. Units 1/100 inch. Default 0 is a thin line.

Gets or sets the color of automatic peak labeling text

Gets or sets a value indicating whether apex labels are drawn on profile plots. When this is not set, the labeling choices (such as LabelMass) only apply to stick plots.

Gets or sets the color of axis grid lines

Gets or sets a value indicating whether axis grid lines are enhanced at zero.

Gets or sets the color of axis grid lines, going through 0,0 Only used when is set.

Gets or sets the thickness of axis grid lines, going through 0,0 Only used when is set.

Gets or sets the color of axis line

Gets or sets the thickness of axis line. Default 0, a thin line.

Gets or sets the color of the axis name

Gets or sets the color of axis numeric values or category labels. This is the color for the text drawn by the major tick marks.

Gets or sets the color for gradient fill of the background

Gets or sets a value indicating whether the background has a gradient fill

Gets or sets the direction of gradient fill for the background

Gets or sets the method of auto scaling

Gets or sets a value indicating whether a box is drawn around peak label text

Gets the peak labeling options

Gets or sets the control size.

Gets or sets the clipboard copy format.

Gets or sets a translator, used to translate mouse position to data position.

Gets or sets a Height in SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the Height SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the width in SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the number of divisions (splits) for X-Axis

Gets or sets a value indicating whether to draw a backdrop in overlaid traces

Gets or sets the elevation for overlaid traces

Gets or sets a value indicating whether Aliasing should be performed. Aliasing creates "jagged" lines, but may avoid any gray appearance on thin lines. Due to improvements in .net 4.0, this is most likely not needed, and default to false.

Gets or sets a value indicating whether or not to enable the ScrollBar below the Plot - default setting: false The Scrollbar simplifies the panning of the plot

Gets or sets a value indicating whether the control's own Context menu is shown. the ContextMenu can be manipulated and added to by the Application using the control it contains certain basic functions, such as Reset Scaling etc.

Gets or sets a value indicating whether the Undo/Redo feature can be used.

Gets a value indicating whether there is at least one available undo action. This can be used to enable a UI element "Undo".

Gets a value indicating whether there is at least one available redo action. This can be used to enable a UI element "Redo".

Gets or sets a value indicating whether methods which create the spectrum (with new scan data) will automatically reset the undo stack. By default: This is "true" such that, if an application user selects a new scan: both "undo" and "redo" become disabled. In addition, many of the methods to set data such as CreateSpectrum overlaods and SetScan overloads) will automatically reset scaling. If "fasle" then a customer may undo a zoom on one scan when viewing a different scan. The scale is also not reset, preserving the zoom range as new data is attached. Note that the resulting data range may have no data in a different scan. However, this feature may be useful to an app which draws 20 scans per second over the same scale (such as a tuning window). Note that all of the the undo and redo records must have the same number of attached scans as the new data, otherwize they are "inconsistent" and always cleared.

Gets or sets the color for sticks of exception-flagged peaks

Gets or sets a value indicating whether the Y-Axis is shown with an exponential scale

Gets or sets a value indicating whether to fix scaling to application provided value

Gets or sets the fixed scaling value (100%), when FixedNormalization is set

Gets or sets the font name

Gets the collection of markers on the current plot

Gets or sets a value indicating whether the plot has negative peaks.

Gets or sets the color used for scan filter field in the plot heading

Gets or sets the color used for labels (prefixes) in the plot heading

Gets or sets the color used for values in the plot heading

Gets or sets an ID for the control

Gets or sets the ImageLabel being dragged and dropped

Gets or sets a value indicating whether the label is permitted to be offset

Gets or sets the number of Decimal places to show.

Gets or sets a value indicating whether plots are labeled with mass

Gets or sets a mass. Peaks are labeled relative to this mass

Gets or sets the threshold (%) for peak labels

Gets or sets the maximum font size (inch)

Gets or sets the maximum number of stacked spectra, which will be drawn (as stick "centroid" or continuous line "profile"), when SpectrumPlotStyle is set to AutoStyle. When more there are more than this number of spectra stacked, the plot will change to a "heat map" (shade) style, as it is assumed that there is insufficient space on the screen to see individual vectors. Default value: 50

Gets or sets the minimum font size (inch)

Gets or sets the method of automatic normalization

Gets or sets the maximum label offset

Gets or sets a value indicating whether to overlay spectrum traces

Gets or sets a value indicating whether panning has been enabled

Gets or sets an interface used by the plot library to generate label strings.

Gets the peaks which have been labeled on this plot

Gets or sets a value indicating whether the plot is waiting for annotation to be completed.

Gets or sets the maximum Y value, as a % of base value

Gets or sets the minimum Y value, as a % of base value

Gets or sets a value indicating whether the Y-Axis is scaled as a percentage

Gets or sets a value indicating whether peak labels to have elbow joins in call-out lines

Gets or sets a value indicating whether to permit an automated heading to re-flow. This property does not affect any "custom headings". The default heading is permitted to wrap fields onto additional lines, when "reflow" is permitted and the plot is too narrow. Text in individual fields is not wrapped, and will shown "..." when too wide.

Gets or sets a value indicating whether spectrum peak labels can be positioned lower than the peak apex

Gets or sets the label precision (decimal places) for m/z labels.

Gets or sets the color for profile if Trace is point to point style

Gets or sets the color for sticks of reference-flagged peaks

Gets or sets a value indicating whether to rotate peak label text

Gets or sets the color for sticks of saturated-flagged peaks

Gets or sets a value indicating whether to apply the same scaling to all overlaid or stacked plots

Gets or sets the height of the ScrollBar in pixels

Gets or sets a value indicating whether the Panning Scroll Bar should be visible or not

Gets or sets the color for the border when the control is selected

Gets or sets a value indicating whether to paint the border round the Spectrum Plot

Gets or sets the skew angle for overlaid traces

Gets or sets a value indicating whether there is smoothing (anti-alias) of profile style traces. This affects rendering quality only, and not the shape of the plot.

Gets or sets the spectrum rendering object

Gets or sets the line drawing style

Gets or sets a value indicating whether X axis is split, into several equal sub ranges

Gets or sets the color for sticks if Trace is stick style, for non-flagged peaks

Gets the collection of text label sets on the current plot. Note: each added label is created as a "set of labels" containing a single label.

Gets or sets the dash style for traces

Gets or sets the thickness for traces

Gets or sets the color for the border when the control is unselected

Gets or sets a value indicating whether to use copy size and resolution from context menu"

Gets or sets the units of custom copy size"

Gets or sets the name to show on X Axis

Gets or sets a value indicating whether the X axis is offset from data

Gets or sets the y axis minimum.

Gets or sets the name to show on Y Axis

Gets or sets a value indicating whether the Y axis is offset from data

Gets or sets the cursor pick

Gets or sets the annotation Manager

Gets or sets the header Manager

Gets or sets the spectrum data.

Gets or sets a value indicating whether to update range scale

This method can be used to add annotations manually

Attribute with parameters for the Annotation Settings Low: position to point to ; High: position for label Low: intensity to point to; High intensity for label Id of the selected Trace

insert new data into a certain trace - invalidates the appropriate section of the plot

id number of trace data to add to end of curve

Clears all Headers from the Spectrum Plot

Clear both UnDo and Redo Stacks

Gets or sets a value indicating whether alpha blended lines can be used, when creating an Emf file. When false: lines are blended with the plot background color, and all text is drawn after all lines. Default=false

Copy the last drawn plot to the clipboard, with a specified image size

width in pixels height in pixels

Copy the last drawn plot to the clipboard, with a specified image size in real world units

width height Units of size

Copy the last drawn plot to the clipboard, using the same size as on screen

Initializes a spectrum plot with a scan and a file name (shown in the heading)

Scan Data from the raw file Full path to the raw file, for display in heading. Flag whether or not to only use the centroid stream data Optional delegate to create a heading. If omitted (or null) a default heading is supplied scanData is null.

Initializes a spectrum plot with a scan. This overload can be used to draw the centroid stream.

Scan Data from the raw file raw file stats for this scan Text of scan filter, for heading Full path to the raw file Data for FTMS/Orbitrap centroids for profile data (can be passed as null) Flag whether or not to only use the centroid stream data. Optional delegate to create a heading. If omitted (or null) a default heading is supplied scanData is null.

Initializes a spectrum plot with a scan and a file name (shown in the heading)

Scan Data from the raw file Full path to the raw file, for display in plot heading (not used to read a file) scanData is null.

Initializes a spectrum plot with a scan. Conversion from scan to "GraphicsScan is custom, as is the heading

Scan Data from the raw file tool to convert a scan to a GraphicsScan Delegate to create a heading (optional) scanData is null.

Initializes a spectrum plot with a scan and a file name (shown in the heading)

Scan Data from the raw file list of filled peaks to draw Full path to the raw file Flag whether or not to only use the centroid stream data Sample the Gaussian about this times as fast as the profile sampling, to make smooth peaks. scanData is null.

Initializes a spectrum plot with a set of scans

scans to plot Titles to show right of each plot

Initializes a spectrum plot with a set of scans, including titles above each scan.

scans to plot Titles to show right of each plot. Set to string.empty if only top titles are needed. Titles at the top of each plot Delegate to create heading for graph Flag whether or not to only use the centroid stream data. Default: false scanData is null.

Initializes a spectrum plot with a set of scans

scans to plot Titles to show right of each plot Delegate to create heading for graph Flag whether or not to only use the centroid stream data. Default: false scanData is null.

Initializes a spectrum plot with a set of scans

scans to plot Titles to show right of each plot Delegate to create heading for graph custom method of converting a scan to a GraphicsScan scanData is null.

Initializes a spectrum plot with a set of scans

scans to plot the list of peaks in scan 0 Titles to show right of each plot Delegate to create heading for graph Flag whether or not to only use the centroid stream data When PPD peaks are drawn, set the amount of interpolation between scans to smooth peak shape scanData is null.

Initializes a spectrum plot with a scan. This overload can be used to draw the centroid stream.

Scan Data from the raw file List of filled peaks to draw raw file stats for this scan Text of scan filter, for heading Full path to the raw file Data for FTMS/Orbitrap centroids for profile data (can be passed as null) Flag whether or not to only use the label data Sample the gaussian about this times as fast as the profile sampling, to make smooth peaks. Thrown when required args are null

Create Spectrum from a single Graphics scan

The spectrum Data.

Create Spectrum from an Array of Graphics scans, with the first scan as the top trace

set of scans to add

Create Spectrum from an Array of Graphics scans

set of scans to add If true, the first scan in the list is on top, else it is at the bottom

Create Spectrum from an Array of Graphics scans

set of scans to add Titles for each scan (shown at right) If true (default), the first trace in the list is on top, else it is at the bottom If true (default), Use the "built in" apex labeler

Create Spectrum from an Array of Graphics scans

set of scans to add Titles for each scan (shown at right) titles at top of trace (may be null) If true (default), the first trace in the list is on top, else it is at the bottom Use the "built in" apex labeler

Create Spectrum from an Array of Graphics scans, with peak color information for each scan.

Array of scans to draw. Data for each scan, about peak series which are specially colored and specially labeled. Must be the same length as "scans". Scans with no color data may have a "null" entry in this array. Strings to use for title on the right (optional). If true (default), Use the "built in" apex labeler

Create Spectrum from an Array of Graphics scans, with peak color information for each scan.

Array of scans to draw. Data for each scan, about peak series which are specially colored and specially labeled. Must be the same length as "scans". Scans with no color data may have a "null" entry in this array. Strings to use for title on the right. May be set to "string.Empty" when only top titles are used. Strings to use for title on the top. If true (default), Use the "built in" apex labeler

ensure that the data attached to this object is set into all records in the undo or redo stack

Save the current SpectrumPlot in the UnDo Stack

Draw the spectrum plot

Plot area Object to draw on

See if the cursor overlaps a label area

Point to test Region found or null if no region found

See if the cursor overlaps a marker

Point to test Region found or null if no region found

Hit test for the a marker

point to test for Cursor Region to test a marker (if hit) or null if not

Save this plot as an EMF format file

file to create If set, output may contain alpha blended (transparent) lines

Save this plot as an HTML format file

file to create

Pan interface

Target percentage to pan Direction to pan - either forward (to a lower Range) or backwards (to a higher Range).

Pan interface

start of pan range end of pan range

Sets the plot back into the state before an Undo was called (if there is one) - Redoes Undoes

Remove all current plots

Replace the collection of markers with a new set. All previous markers will be removed from the object, and the attached plot. The new markers will be attached to the plot.

New set of markers

Replace the collection of text annotations with a new set. All previous text annotations will be removed from the object, and the attached plot. The new text annotations will be attached to the plot.

New set of annotations

Reset the scaling to the data max values

become selected or not

True if the plot must be shown as selected.

Add header

Handles toggling of ControlSelection

Object that raised the event EventArgs for this Event (Selected, ControlId)

Scrol to a new X range

new start of range new end of range

Enable or disable panning mode

toggle plot between selected and unselected

Sets the Plot back to the last state before the last Do was called - Undoes changes

Description of change needed to amplifiers

Description of the annotation

Description on the annotation

Expand horizontal

true if graph is changed

Expand vertical scale (zoom in)

true if graph is changed

Expand vertical axis.

The factor (for example 2 to see twice the detail). If the displayed range contains the value zero, then expand such that the positive and negative offsets from zero are halved (keeping the relative zero position). If not set or if zero is not within the range: follow the rules based on the setting of "fromMidPoint" Zoom to keep the mid point of the Y scale the same (else keep the lowest value the same). Note that this is overridden if preserveZero is set, and the current range includes or ends at zero. True if expanded

contract horizontal scale by a factor

true if graph is changed

Contract vertical axis.

The factor (for example 2 to see half the detail). If the displayed range contains the value zero, then contract such that the positive and negative offsets from zero are increased, keeping the relative zero position. If not set or if zero is not within the range: follow the rules based on the setting of "fromMidPoint" Zoom out to keep the mid point of the Y scale the same (else keep the lowest value the same). Note that this is overridden if preserveZero is set, and the current range includes or ends at zero. True if expanded

zoom out in y: contract vertical scale

True if graph was changed

Draw method

Rectangle bounds to draw where to draw

The initialize values from test case.

The details. The x. The y.

Print Page

Rectangle to print Graphics to print

Create demo data for designer mode.

Measures the child elements of a in anticipation of arranging them during the pass.

A that represents the size that is required to arrange child content. An upper limit that should not be exceeded.

Invoked when an unhandled attached event reaches an element in its route that is derived from this class. Implement this method to add class handling for this event.

The that contains the event data. This event data reports details about the mouse button that was pressed and the handled state.

Invoked when an unhandled attached event is raised on this element. Implement this method to add class handling for this event.

The that contains the event data.

Invoked when an unhandled routed event is raised on this element. Implement this method to add class handling for this event.

The that contains the event data. The event data reports that the left mouse button was pressed.

Invoked when an unhandled routed event reaches an element in its route that is derived from this class. Implement this method to add class handling for this event.

The that contains the event data. The event data reports that the left mouse button was released.

Invoked when an unhandled attached event reaches an element in its route that is derived from this class. Implement this method to add class handling for this event.

The that contains the event data.

Key pressed

Draws the content of a object during the render pass of a element.

The object to draw.

Convert boolean "visible" to the visibility enumeration.

If the item should be visible. The appropriate value for visibility (on or off)

Make an empty heading.

The block.

The add labels.

The labels. The trace id.

The adorner actions for mouse down.

The apply undo redo.

The plot.

Clear the adorner.

The adorner layer of this control

clear marker box.

complete a pick.

true if the adorner layer must be cleared. When an object is selectable, then it may remained as selected, and not cleared.

configure the plot heading.

The create heading.

The configure undo redo.

The menu. The enable.

convert scans.

The scan data. The converter. The converted scans Thrown if any scan in the collection is null

copy to clipboard tool strip menu item clicked. Perform copy.

The sender. The event args.

count title lines.

The top titles. The number of lines

Create cross hair.

The create peak envelope shape.

The peak. The scan item. The n peak number. The trace. The over sample.

Create peak highlight.

The start region (where the mouse was moved)

Create a rubber band shape.

The cursor region. The style.

Highlight a peak label, which can be selected

The default settings.

Create color and thickness of adorner

Describes the adorner A Tuple of line color, fill color, thickness

Gets or sets the line tickness of the pick marker. This is any marker created after the left button is held down and dragged. Default 0: thin line

Get background mask, which should make a visible adorner. The transparency is adjusted, if the adorner has a rectangle, so that more of the plot behind can be seen.

The line draw. The fill color to use for the adorner.

get a background mask.

A color, for use by adorner lines

Get the display rectangle.

The size of the graph area (with space for scroll bar removed)

The handle amplify.

The start. The end.

Handle annotation.

The start. The end.

Handle graphic marker.

The start. The end.

Handle trace selection.

The start.

handle x axis zoom.

The range. The handle x axis zoom.

Handle y axis zoom.

The range. True if zoomed.

The initialize scroll bar.

Initialize the spectrum.

The control dimension. The initialized spectrum plot.

Create Spectrum from a single Graphics scan This version allows internal code to set the peak labelling mechanism, from "Label data" etc.

The spectrum Data.

The internal reset scaling.

The internal set aliasing.

The value.

Test if a selectable marker has been selected, and if so, start the drag

True, if drag started

Test if a draggable marker has been selected, and if so, start the drag

True, if drag started

Make a default heading.

The block.

The on control panned.

The e.

Control-Scrolled EventHandler. Triggered when scroll bar is moved

On control scrolled. Called when the scroll bar has moved.

The event args. New X data limits.

The on control selected.

The e.

Handle whether to delete of image label being dragged/clicked when Delete key is hit.

Key pressed

The on graph amplified.

The e.

The on graph annotation changed.

The e.

The on graph region selected.

The e.

The label was clicked twice.

The e.

The on moved over graph.

The event.

The on property changed.

The e.

The on reset scaling.

The e.

Perform pan (drag plot left/right)

The plot scroll bar_is scrolled

The sender. The e.

The raise graph region selected event.

The start. The end.

Range has changed.

The new range. Always returns true

Handle a range selection on the Graph - annotation, selection, amplifying and zooming

Object that raised the Event Arguments passed through the Event

The readapt control settings.

show scroll bar if needed. It is not needed if the plot has become full range

The plot base.

Re do was clicked.

The sender. The event args.

Render the pick marker.

The adorner shape. The color.

Render the pick marker.

The shape to draw. The color, as "line color, fill color, thickness"

The reset click.

The sender. The e.

reset the scrollbar (full X range).

Attach annotations (custom text) to the spectrum plot.

Attach markers (custom graphics) to the spectrum plot.

Attach a scan to a spectrum control.

data from FT label stream (may be null) Full path to the raw file Text to show for the scan filter Retention time of scan Scan, as previously read from the raw file delegate to create plot heading

Attach a scan to a spectrum control.

data from FT label stream (ma be null) Full path to the raw file Text to show for the scan filter Retention time of scan Scan, as previously read from the raw file list of filled peaks to draw Oversampling for PPD peaks. Larger values give smoother peaks

The spectrum context menu strip_ opened.

The sender. The e.

The spectrum plot control property changed.

The sender. The e.

The undo_ click.

The sender. The e.

The update plot scroll bar.

The range.

This class can be configured to convert scans to GraphicsScans which can be renedered, using properties to control what section of the scan data is converted. It can also be used to attach colors to the individual peaks in the scan. The scan sent to the converter has to be of type "ScanWithColors"

Return the set of colors for this scan

Scan requiring colors Colors to use with this scan

Gets or sets a value indicating whether or not to only use the centroid stream data. When set the "segmented scan" is ignored, and sticks are plotted based on the centroid stream.

A standard conversion from Scan to GraphicsScan. Using properties of this class, and available data in the scan, the scan is converted to "GraphicsScan" format for drawing.

Scan to be converted Converted scan

InitializeComponent

Interaction logic for WpfXYPlotControl.xaml

WpfXYPlotControl

Initializes a new instance of the class. Default constructor

Name for identifying a retention time marker

Gets or sets the cursor pick

Gets or sets a value indicating whether the Panning Scroll Bar should be visible of not

Gets or sets the Id data

Gets the internal plot object. Note: This method is not recommended for use by clients. It maybe factored out in future. Currently needed to support certain peak labeling features.

Gets the cursor translator, which is used to translate screen position to data position.

Gets or sets a value indicating whether the plot is waiting for annotation to be completed.

Gets or sets the control size.

Gets or sets the Color for the border when the Control is unselected

Gets or sets the Color for the border when the Control is selected

Gets or sets the color for gradient fill of the background

Gets or sets a value indicating whether the gradient fill the background

Gets or sets the direction of gradient fill for the background

Gets or sets a value indicating whether to display the X Position marker. This is a red line, which can be used to highlight the last point selected from a plot.

Gets or sets the X Coordinate to display the marker

Gets or sets a value indicating whether the default GraphRegionSelectionEvent is automatically handled or not - registers and deregisters the default method for Event Handling of GraphRegionSelection

Gets or sets a value indicating whether the Undo/Redo feature is enabled

Gets a value indicating whether there is at least one available undo action. This can be used to enable a UI element "Undo".

Gets a value indicating whether there is at least one available redo action. This can be used to enable a UI element "Redo".

Gets or sets a value indicating whether this control has a context menu. this switches the control's own Context menu on or off. the Context Menu can be manipulated and added to by the Application using the control it contains certain basic functions, such as Reset Scaling etc.

Gets or sets a value indicating whether or not to enable the ScrollBar below the Plot - default setting: false The Scrollbar simplifies the panning of the plot

Gets or sets the line drawing style

Gets or sets a value indicating whether smoothing (anti-alias) of connected line style traces. This affects rendering quality only, and not the shape of the plot.

Gets or sets a value indicating whether to overlay chromatogram traces

Gets or sets the skew angle for overlaid traces.

Gets or sets the elevation for overlaid traces

Gets or sets a value indicating whether to Draw a Backdrop in overlaid traces

Gets or sets a value indicating whether to rotate peak label text

Gets or sets a value indicating whether to box peak label text

Gets or sets the threshold (%) for peak labels

Gets or sets the maximum label offset

Gets or sets a value indicating whether peaks labels are permitted to be automatically offset from the peaks.

Gets or sets a value indicating whether the X axis is offset from data

Gets or sets a value indicating whether axis is offset from data

Gets or sets a value indicating whether the X axis is split, into several equal sub ranges

Gets or sets the number of divisions (splits) for the X-Axis

Gets or sets a value indicating whether to scale the Y-Axis as percentage

Gets or sets a value indicating whether the Y-Axis is shown with an exponential scale

Gets or sets the X-Axis name

Gets or sets the name to show on Y Axis

Gets or sets the color of axis line

Gets or sets the color of axis grid lines

Gets or sets the color of axis grid lines, going through 0,0 Only used when is set.

Gets or sets the thickness of axis grid lines, going through 0,0 Only used when is set.

Gets or sets a value indicating whether axis grid lines are enhanced at zero.

Gets or sets a value indicating whether Horizontal axis grid lines are enabled

Gets or sets a value indicating whether there are Vertical axis grid lines

Gets or sets a value indicating whether there are sparse axis grid lines

Gets or sets the Thickness of axis line. Default 0, a thin line.

Gets or sets the color of axis name

Gets or sets a value indicating whether the plot has Aliasing. Aliasing forces sharp single pixel lines, but also give jagged edges. Due to improvements in .net 4.0, this is most likely not needed, and default to false.

Gets or sets the color of axis numeric values or category labels. This is the color for the text drawn by the major tick marks.

Gets or sets the Method of auto scaling

Gets or sets a value indicating whether the plot is scaled to an application provided value.

Gets or sets the fixed scaling value (100%), when is set

Gets or sets the method of automatic normalization.

Gets or sets the Minimum Y value, as a % of base value

Gets or sets the maximum Y value, as a % of base value

Gets or sets a value indicating whether to apply the same scaling to all overlaid or stacked plots

Gets or sets a value indicating whether to Label peaks on the plot with X data values

Gets or sets the precision used for peak labels.

Gets or sets the maximum font size (inch)

Gets or sets the maximum size of fonts to use, in inches high

Gets or sets the minimum size of fonts to use, in inches high

Gets or sets the clipboard copy format.

Gets or sets the table of colors for traces. Colors are cycled for larger numbers of traces

Gets or sets the table of thickness for traces. Thicknesses are cycled for larger numbers of traces

Gets or sets the table of Dash Style for traces. Dash Styles are cycled for larger numbers of traces

Gets or sets the location of legend for category style plot

Gets or sets the width of legend for category style plot, when legend is left or right

Gets or sets the width of graph for category style plot, when legend is left or right. If the plot area is smaller than this, then the legend is not drawn

Gets or sets a value indicating whether to use copy size and resolution from context menu"

Gets or sets the width in SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets a Height in SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the Height SizeUnits (as set by CopyUnits) for custom copy feature"

Gets or sets the units of custom copy size"

Initialize the chromatogram

This method completes setup of the chromatogram, after all traces have been added by the calling application.

Create a plot with a series of traces and a category axis, This sets all styles for a chart (overrides many designer settings) if requested. To create a more custom chart, with different headings, legends and other styles use the overload "CreateCategoryPlot(string[]categories, double[][] dataSeries)" and use "SetHeading" to design a heading as needed

The names of the categories, such as month names The series of data to be added. Each series must be the same length as the categories String shown at top of chart Color of legend if this is true, styles are set to defaults for a chart overriding various designer properties) margin is added to the data range, so that the first and last categories are not at the edges of the plot. For example: "0.5" to add "half a category" at each side Optional. For plots of unrelated categories ("Dog", "Cat" etc.) this should be null. If the data repesents related numeric data, where each bar represents a numeric value on the X scale, then this data will be used to create an X axis scale. Thrown if categories or dataSeries is null Thrown if the data series are not all the same length

Create a plot with a series of traces and a category axis, such as "Jan, Feb, March" and data series for each category. This method only sets the data. The designer should set other styles (such as overlay=true, elevation=0, axis titles, line styles) as needed. See overloads for greater convenience for standard chart styles

The names of the categories, such as month names The series of data to be added. Each series must be the same length as the categories margin is added to the data range, so that the first and last categories are not at the edges of the plot. For example: "0.5" to add "half a category" at each side Thrown if categories or is null Thrown if the data series are not all the same length

Method to add one or more traces to the plot

Time data, first index is trace, second is set of values per trace Intensity data, first index is trace, second is set of values per trace Number of traces to add traceId of the trace just added

Remove all current plots

Add header

Clear all headers from the Plot

Change "select" attribute for plot

Pan the graph X axis by a percentage of the X axis range

Percentage to pan Direction to pan - either forward or backwards.

Pan to a new range

start of pan range end of pan range

Description of change needed to amplifiers

Description on the annotation

This method can be used to add annotations manually

Attribute with parameters for the Annotation Settings Low: position to point to; High: position for the PeakLabel Low: intensity to point to; High intensity for the PeakLabel Id of the selected Trace

Descrition on the annotation

Move the X Position marker to a new position

The new marker position

Test if a point hits a marker on the plot.

point to test hit for region in which to test for hit a CursorCrossHair Style

Hit test for peaks

point to hit test for region in which to hit test for peaks point to store valid pick start data in for this region True if the right end of the marker has been picked Time of the fixed end of the peak baseline (the end not being dragged) Intensity of the fixed end of the peak baseline (the end not being dragged) an IXYData object

Print page

Bounding rectangle Graphics to draw to

Print Page Handler

Rectangle bounds to print graphics to print

Given a rectangle and graphic, draw a chromatogram

The bounds in which to draw the chromatogram The graphic area on which to draw the chromatogram

Creates data for the designer view

Measures the child elements of a in anticipation of arranging them during the pass.

A that represents the size that is required to arrange child content. An upper limit that should not be exceeded.

Add traces with a symbol for each point.

The data series.

The create legend.

The data series. The chart title. The legend text color.

The make legend.

The data series. The chart title. The legend text color. The legend When the LegendPosition is not valid

Gets or sets a value indicating whether data series names, and color bars, are shown in the legend for a category plot. If not shown: Only the "title" is shown as a legend.

The add category plot traces.

The categories. The data series. Optional. For plots of unrelated categories ("Dog", "Cat" etc.) this should be null. If the data repesents related numeric data, where each bar represents a numeric value on the X scale, then this data will be used to create an X axis scale. The margin.

The add x position marker.

The handle amplify.

The start. The end.

The handle x axis zoom.

The range. True if zoomed.

Handle y axis zoom.

The range. true if zoomed.

Handle x update.

The start.

Handle trace selection.

The point where the mouse was clicked.

The handle x value update.

The x value. The trace id.

The handle annotation.

The start. The end.

handle graphic marker.

The start. The end.

The handle graphic marker.

The start. The end.

The set annotation.

The update x position.

The time.

The raise graph region selected event.

The start. The end.

The update rubber band.

Handles a range selection on the Graph

Object that sent the Event Arguments passed through the event (Range in Pixels and Data Values)

The update tracking cursor.

The perform pan.

The render pick marker.

The line draw. The color.

Get background mask, which should make a visible adorner. The transparency is adjusted, if the adorner has a rectangle, so that more of the plot behind can be seen.

The line draw. The fill color to use for the adorner.

clear the adorner.

The adorner layer for this control

get a background mask.

A color, for use by adorner lines

The xy plot control_ property changed.

The sender. The e.

Invoked when an unhandled attached event is raised on this element. Implement this method to add class handling for this event.

The that contains the event data.

Begin tracking of mouse drags, on mouse down.

Mouse position

Begin rubber banding.

Create rubber band shape.

The region. The style.

Handle move pan or drag actions as mouse moves

The MouseEventArgs

Handle mouse up action on plot

Mouse position

Complete the pick.

Redraw the control

Context where control is rendered

get the display rectangle

Size of the plot

Handle key down: up and down arrows expand and reduce vertically

Key pressed

Handle events for retention time being selected from a plot

The on retention time selected.

The e.

Handle events for mouse moving over a plot

The on moved over graph.

The e.

Handle events for retention time being selected from a plot

The on manual baseline selected.

The e.

Graph Region Selected Event handler

The on graph region selected.

The e.

EventHandler for catching, when Graph Scaling has been reset

The on reset scaling.

The e.

Control-Panned EventHandler

The on control panned.

The e.

Control-Scrolled EventHandler. Triggered when scroll bar is moved

On control scrolled. Called when the scroll bar has moved.

The event args. New X data limits.

Graph-Amplified EventHandler

The on graph amplified.

The e.

Graph-Annotated EventHandler

The on graph annotation changed.

The e.

Raise Control Selection Event

The on control selected.

The e.

The property changed.

The on property changed.

The e.

Gets a value indicating whether the Control is actively selected

Handles toggling of ControlSelection

Object that raised the event EventArgs for this Event (Selected, ControlId)

Expand vertical axis.

The factor (for example 2 to see twice the detail). If the displayed range contains the value zero, then (with, for example, a factor of 2) expand such that the positive and negative offsets from zero are halved (keeping the relative zero position). If not set or if zero is not within the range: follow the rules based on the setting of "fromMidPoint" Zoom to keep the mid point of the Y scale the same (else keep the lowest value the same). Note that this is overridden if preserveZero is set, and the current range includes or ends at zero. True if expanded

Contract vertical axis.

Expand vertical

true if graph is changed

contract horizontal scale by a factor

true if graph is changed

reset the scrollbar (full X range).

Expand horizontal

true if graph is changed

contract vertical scale

True if graph was changed

Reset the scaling to the data max values

Gets or sets a value indicating whether panning has been enabled

Enable or disable panning mode

Save the current ChromatogrammPlot in the UnDo Stack

Sets the Plot back to the last state before the last Do was called - Undoes changes

Sets the plot back into the state before an Undo was called (if there is one) - Redoes Undoes

Clear both UnDo and Redo Stacks

apply undo redo.

The plot.

The readapt control settings.

The reset_ click.

The sender. The e.

The re do button was clicked.

The sender. The event args.

The undo button was clicked.

The sender. The event args.

Gets or sets a value indicating whether alpha blended lines can be used when creating an Emf file . Default=true

copy to clipboard tool strip menu item clicked. Perform copy.

The sender. The event args.

Copy the last drawn plot to the clipboard, with a specified image size in real world units

width height Units of size

Copy the last drawn plot to the clipboard, using the same size as on screen

Copy the last drawn plot to the clipboard, with a specified image size

width in pixels height in pixels

The xy plot context menu strip_ opened.

The sender. The e.

The initialize scroll bar.

The update plot scroll bar.

The range.

The plot scroll bar_ scroll.

The sender. The e.

Save this plot as an EMF format file

file to create If set, output may contain alpha blended (transparent) lines

Save this plot as an HTML format file

file to create

Scrol to a new X range

new start of range new end of range

InitializeComponent

Contains Amplifying settings

Initializes a new instance of the class. Constructor - Creates EventArgs for Amplified Event

amplify Enabled flag amplify clear region flag factor by which to amplify start of amplifying region end of amplifying region Id of the Control raising the event

Gets a value indicating whether Amplifier is enabled.

Gets a value indicating whether all amplifiers are to be cleared.

Gets Factor by which to amplify

Gets the start point of Amplifying region

Gets the end point of Amplifying region

Gets the Control Idenfication Information (name, type, Id)

Contains EventAgs for Annotations

Constructor - Creates EventArgs for Amnnotating Event

Start Point (Pixel) of annotated Region End Point (pixel) of annotated Region XDataRange of annotated region YDataRange of annotated region id nr of the selected trace Id of the Control raising the event

Start point of Annotating region

Gets the XAxis DataRange of the Annotated Region

Gets the YAxis DataRange of the Annotated Region

Get the id Nr of the currently selected Trace

Returns the Control Idenfication Information (name, type, Id)

Contains X,Y data from a graph (in data space, not pixels)

Initializes a new instance of the class. Create an event for a mouse movement. Translates X and Y data from the plot

X data position Y data position

Gets the X data value at the mouse position

Gets the Y data value at the mouse position

EventArgs containing selected Region in Pixels and DataValues

Gets or sets a value indicating if this event has been handled. Emulates feature of "Routed event args".

Initializes a new instance of the class. Create EventArgs for A GraphRegionSelected

range of points - pixel coordinates to zoom to range of XValues to zoom to range of YValues to zoom to ControlIdentification Id - Control that raised the ZoomedEvent Zero based trace from which the range was selected. Default "-1", not from any trace

Initializes a new instance of the class. Create EventArgs for A GraphRegionSelected

range of points - pixel coordinates to zoom to range of X Values to zoom to range of Y Values to zoom to range of Z Values to zoom to Data type of Z scale ControlIdentification Id - Control that raised the ZoomedEvent Zero based trace from which the range was selected. Default "-1", not from any trace

Gets the Control Identification Information (name, type, Id)

Gets the selected Range in Pixel Coordinates (Point High, Point Low)

Gets a value indicating whether the X PixelRange is significant. True If the range is more than 3. Zoom will not occur if the range is not greater than 3.

Gets a value indicating whether the Y PixelRange is significant. True If the range is more than 3. Zoom will not occur if the range is not greater than 3.

Gets the selected X Range in Data Values - ordered

Gets the selected Y Range in Data Values - - ordered

Gets the selected Z Range in Data Values - - ordered

Gets the selected Z type

Gets the trace that this was picked from

Defines features of an image label

Gets or sets the image to be drawn

An Interface for implementing the Scrol bar support in plot controls - Enables interaction between Controls

Pan interface

start of pan range end of pan range

Defines commands specific to Wpf rendering

Draw an image

Image to draw bounding rectangle of image

Class to draw ion maps. An Ion map is used to show all MS/MS transitions or a particular order. The map has precursor masses on one axis, and fragments on the other

The max precursors.

The tolerance.

The scan filter for MS 2.

The scan filter for MS 10.

Gets or sets the MS/MS order for the map. Default 2 (MS/MS). For MS/MS this makes a map of all MS/MS precursors and fragments. Order 3 would give MS/MS/MS precursors and MS/MS fragments, and so on.

The range info.

Initializes a new instance of the class. Default constructor

Initializes a new instance of the class. Copy the ion map settings

Ion map to copy

Creates the map internal data, from the supplied data source. Must be called prior to drawing.

A data source, which supplies scans to the map

Gets or sets the data source.

Draw the ion map, using data created with the last call to

Drawing surface

Gets or sets the header Manager

Add header

Create heading.

The block.

clear allocated tables

Reset the range limits according to the flags.

set to full precursor Mass range

True if there is data to plot

Set the mass limits for the map. Setting a range of "0.0,0.0" will case an auto range (full product range) at the next draw

The product mass range always returns true

get displayed Precursor Mass range

The precursor mass range (X axis limits)

Gets the range of masses for the plot

Gets displayed mass range

The (product) mass range of the plot

The sort struct.

compare masses.

Compare, to sort by mass.

The first value to compare. The second value to compare. The comparison result.

Read all traces.

The source.

The convert index to scan number.

The matched indexes. The index. The .

The extract scans.

The source. The matched indexes. The peak count. The multiple indexes. The width of each trace. The first trace start.

The extract scan.

The raw Scan. The index. The source. The matched indexes. The .

The calculate mass limits for file.

The source. The matched indexes. The peak count. The .

The initialize precursor mass limits.

override the set traces, to use a subset of the data

number of scans start of mass range to plot (range in z-axis 3D map, y-axis in density mapping end of mass range to plot (range in z-axis 3D map, y-axis in density mapping The start of the created data for the map (allows a slice of the data to be plotted) chromatogram for each scan trace which is all zero RT at each scan What trace type, used for what cursor to display data type for X Axis, such as "time" or "precursor"

Create a product mass scan, from the current map

The source. Parent mass, whose product scan is needed The extracted product scan

This produces a precursor scan, from the current map

The source. Generate precursors for this product The extracted precursor scan

This produces a Neutral Loss scan, from the last drawn map.

The source. Mass of neutral The extracted neutral loss scan

Calibration curve plot

Gets or sets Color for the calculated amount marker line.

Initializes a new instance of the class. Constructor

Initializes a new instance of the class. Copy Constructor

Plot to Copy

Set the symbol colors for both the include and excluded symbol

Color to set the symbol color

Gets or sets the color used for the symbol for points included on the calibration curve

Gets or sets the color used for the symbol for points excluded from the calibration curve

Gets or sets the color used for the symbol for points included on the calibration curve

Gets or sets the color used for the symbol for points excluded from the calibration curve

draw the curve.

The context.

Follow steps 1a or 1b and then 2 to use this custom control in a XAML file. Step 1a) Using this custom control in a XAML file that exists in the current project. Add this XmlNamespace attribute to the root element of the markup file where it is to be used: xmlns:MyNamespace="clr-namespace:ThermoFisher.CommonCore.WpfPlot" Step 1b) Using this custom control in a XAML file that exists in a different project. Add this XmlNamespace attribute to the root element of the markup file where it is to be used: xmlns:MyNamespace="clr-namespace:ThermoFisher.CommonCore.WpfPlot;assembly=ThermoFisher.CommonCore.WpfPlot" You will also need to add a project reference from the project where the XAML file lives to this project and Rebuild to avoid compilation errors: Right click on the target project in the Solution Explorer and "Add Reference"->"Projects"->[Browse to and select this project] Step 2) Go ahead and use your control in the XAML file.


                < MyNamespace:ChroDerivedControl >

Create from a chromatogram plot

default constructor

Create designer view data

access to cursor

Emulate mouse down

Emulate mouse move

Emulate mouse up

Emulate mouse leave

Create data for designer mode

This class produces a chromatogram graphics report, which can have any number of traces. This layer supports WPF syntax for colors. WPF based wrapper.

Initializes a new instance of the class. construct

Reset scaling to "auto".

Initializes a new instance of the class. Copy constructor

chromatogram to copy

Creates a new object that is a copy of the current instance.

A new object that is a copy of this instance. 2

Draw the chromatogram

WPF drawing surface

Class to delete image labels

Gets or sets a label, such that any label matching it will be removed

Determine whether the given label should be deleted

a label of ImageLabel type true if the label should be deleted; false otherwise.

Clear annotation matching the given image label

image label object to be deleted

Object to use win32 system to make EMF metafiles on clipboard

Place a metafile on the clipboard

window handle metafile reference true if object created on clipboard

Windows system calls

Event from graphs (mouse clicks etc)

General information for every control Used for Activate data

Gets or sets The name for this control

Gets or sets An id used by the application to track

Gets or sets A tag that identifies the type of this plot

Initializes a new instance of the class. Constructor

The name for this control An id used by the application to track A tag that identifies the type of this plot

Contains wether or not a Control was selected ot unselected

Create EventArgs for a Control Selection Event

wether or not the Control was selected or unselected ControlIdentification (name, type, id)

Returns wether or not the Control was selected or not

Returns the Control Idenfication Information (name, type, Id)

The plot scroll bar support class maps Windows scroll bar activity into X data range changes on a plot.

Initializes a new instance of the class.

The plot scroll bar.

Initialize the scroll bar.

Set if the scroll bar should be enabled (shown). The graph, which is controlled by the scroll bar.

Convert data value to scroll range.

The value. The start. The scale. The scroll bar position>.

Update the plot scroll bar.

The range. The enable. The graph.

Scale factor between scroll position and data.

The graph. The scale factor.

Scroll to a new x axis range.

The control. The graph. The event. Thrown on invalid scroll event

Scroll to new value.

The control. The graph. The event.

Scroll to start of plot.

The control. The graph.

Scroll to end of plot.

The control. The graph.

Class to draw using WPF drawing context.

Initializes a new instance of the class.

The context.

Gets or sets a value indicating whether to work around a WPF defect. return "false" from all other renderers This is to workaround a defect in WPF If an adorner control is drawn, and the control below has "exact integer" pixel coordinates for vertical lines, then there is a clipping error, and lines just to the left of the adorner are erased from the adorned element when the adorner is drawn.

This is to workaround a defect in WPF If an adorner control is drawn, and the control below has "exact integer" pixel coordinates for vertical lines, then there is a clipping error, and lines just to the left of the adorner are erased from the adorned element when the adorner is drawn.

Point to be adjusted A fixed value: If x is an exact integer, 0.1 is added so that it is a "real" value

Point to be adjusted A fixed point: If either x or y are exact integers, 0.1 is added so that they are "real" values

Create a pen. This may save overheads of creating pens on each interface call which accepts "PlotPen"

The pen to convert. An object which contains the converted pen. This can only be used by the renderer which provided it.

Draw an ellipse

Brush to fill ellipse, if not null Pen for ellipse outline, if not null Center of ellipse Width of ellipse Height of ellipse

Draw a figure from a set of points, in a sparse array. This method permits a buffer to be allocated for a set of points, and to be partially filled from the start.

Brush to fill figure Pen for outline Points defining outline Number of points to draw, always starting at index 0 True if the figure should be filled If true: Figure is closed. Example: a rectangle given a 4 points would appear correctly when closed, but as 3 sides when not closed

Draw a figure from a set of points, in a sparse array. This method permits a buffer to be allocated for a set of points, and to be partially filled from the start.

Brush to fill figure Pen for outline, crated by this renderer Points defining outline Number of points to draw, always starting at index 0 True if the figure should be filled If true: Figure is closed. Example: a rectangle given a 4 points would appear correctly when closed, but as 3 sides when not closed

Draw a rectangle, filled with a solid color

Color to fill with Rectangle to fill

Draw a rectangle, filled with a gradient

First color of gradient Second color of gradient Angle and other attributes of gradient Rectangle to fill

Draw an image

Image to draw bounding rectangle of image

Draw a line

Pen for line Start of line End of line

Draw a line

Pen for line Start of line End of line

Draw a set of lines

Pen for line The lines to draw

Draw a path (a set of lines). If the brush is set, but not the pen, then a pen is created from the bush.

Brush to fill path (if not null) Pen for outline (if not null) Path to draw

Draw a Rectangle

Brush, to fill if not null Pen for outline, if not null Rectangle to draw

Draw a Rectangle

Brush, to fill if not null Pen for outline, if not null Rectangle to draw

Draw a string rotated at an angle

String to draw Font to draw Clockwise angle from horizontal X position of text Y position of text Brush to paint text Alignment of text

Draw a text string

Test to draw Font to use Brush to draw text X coordinate Y coordinate

Draw a text string

Text to draw Font to draw in Brush to draw text X coordinate Y coordinate String alignment

Calculate size in display units of a string, when set an an angle

Text to measure Font to measure Angle of text String alignment The size of the rotated string

Measure a string, not including any space around the text

Text to measure Font to measure with The size of the string

Stop clipping (from last Push Clip)

Pop last interpolation.

end use of guidelines (WPF only)

Pop last smooth.

Begin clipping.

Clip region

Push interpolation mode for bitmaps

set if the interpolation should look smoothed

Push a guideline set (WPF only). This is to cause pixel aligned lines.

Begin smoothing, must have a matching PopSmooth call.

Convert a color.

The color to convert. The converted color.

Convert a dash style.

The style to convert. The converted style.

Convert a pen.

The pen to convert. The converted pen.

Convert region.

The rectangle region. The converted region.

Convert to brush.

The brush to convert. The converted brush.

Create a guideline set, to get "crisp" pixels..

The half pen width. The rectangle. The created guidelines.

Convert an alignment.

The alignment to convert. The converted alignment. Unknown alignment

convert a type face. Keeps a cache of types.

The font, who's face is needed. The converted face.

Convert a figure.

The plot path figure to convert. The converted figure.

Convert font family.

The font family to convert. The converted font family.

Convert a font style.

The style to convert. The converted style. Unknown style

Convert a font weight.

The weight. The converted weight. Unknown weight

Convert a path geometry.

The path to converted. The converted geometry.

Convert a point.

The point to convert. The converted point.

Convert a segment.

The plot line segment to convert. The converted segment.

The WPF render pen.

Initializes a new instance of the class.

The pen.

Gets the brush used to paint this pen

Gets the converted pen.

Gets the style of dashed lines.

Gets or sets the initial pen.

Gets the width (points) for this pen.

Performs application-defined tasks associated with freeing, releasing, or resetting unmanaged resources.

Class to render the data in a format suitable for EMF files.

Initializes a new instance of the class.

graphics, used for rendering If set, output may contain alpha blended (transparent) lines

Draw an image

Image to draw bounding rectangle of image

Draw a geometry.

The shape. The plot brush. The plot pen. The bounding rectangle.

Convert (as best we can) WPF specific rendering to generic rendering

Draw a geometry.

The shape. The plot brush. The plot pen. The bounding rectangle.

update cursor to match mouse movement returns data value and data type at selected point

Cursor style for selection

intersecting lines: Designed for mouse over

arrow at one end.

arrow at both ends

horizontal line

a square

box from cursor region: Designed for mouse over

Gets style to draw the cross hair

Gets or sets a value indicating whether to draw cross hair

Gets or sets the style chosen, (same as m_style except when 'Automatic')

Color of cursor line

Initializes a new instance of the class. Constructor

half of cross hair width

Clear the cursor

Change the marker style

New style

This function is called when just moving the mouse cursor over the graph when no mouse operation is in progress

device context to draw on region for this point mouse point

This function is called when a cursor operation has been performed on a trace the resultant action is applied to a different trace, it calculates the rigid cursor imprint on the source trace

shape to draw on cursor input database Start Point (Skewed) mouse point (Skewed), but adjusted if close enough to a line and not a thin box Cursor Pick already containing all the details of what to draw

This function is called when a cursor operation has been performed on a trace the resultant action is applied to a different trace, it calculates the rigid cursor imprint on the source trace

shape to draw on cursor input database Start Point (Skewed) mouse point (Skewed), but adjusted if close enough to a line and not a thin box Style used by the cursor pick Shift due to skew by the cursor pick

update a box cross hair.

The endpoint. The xshift due to skew. The start point.

This function is called when we want a marker displaying on the graph where we have only the data points by which to draw the line by, we don't have any mouse points. Hence we have to examine the cursor input base for a valid region and then draw a CrossHair on it. Used by ion maps.

shape to draw cursor on recorded cursor regions Marker must pass through this Data value What trace type should the graph be What type of marker we want on the graph, also used to determine axis for data value

Create a wide horizontal cursor.

The data value. The region. The tan skew. The start. The bounds rectangle. The end.

The create wide vertical cursor.

The data value. The region. The tan skew. The start. The bounds rectangle. The end.

create a cursor with single arrow at top.

The data value. The region. The tan skew. The start. The bounds rectangle. The end.

The create wide neutral loss cursor.

The data value. The p region. The d tan skew. The start. The end.

Draw the cross hair cursor

shaape in which to draw

The draw square marker.

The shape.

The draw plain square marker.

The shape.

The draw skewed square marker.

The shape.

The draw skewed decorative corner right bottom.

The shape.

The draw decorative corner right top.

The shape.

The draw decorative corner left bottom.

The shape.

The draw skewed decorative corner left top.

The shape.

The draw skewed rectangle.

The shape.

The draw box marker.

The shape.

The draw plain square.

The shape.

The draw flat marker.

The shape.

The draw two arrow marker.

The shape.

The draw one arrow marker.

The shape.

The draw cross hair.

The shape.

The draw small cursor.

The shape.

The move to.

The p.

The move to.

The x. The y.

The rubber band line to.

The shape. The x. The y.

Draw a rubber band line (for tracking cursor)

shape to draw on, to be rendered in an Adorner End point of line

A cursor pick is the on-screen representation for cursor input. The class is for selecting data from a user interface (control) It is designed to handle "rubber band" interactions on a plot. A line, rectangle or parallelogram is drawn to represent the selection currently being made (whilst the mouse is dragged across a graph).

Default number of pixels before a line becomes a box. For example: 1: A line is dragged horizontally 30 pixels, and vertically 5 pixels. In this case the customer is assumed to be drawing a horizontal line, to zoom in X. 2: A line is dragged horizontally 30 pixels, and vertically 10 pixels. In this case the customer is assumed to be drawing a box, to zoom in X and Y.

where pick was started, Note this is a window co-ordinate point, no anti skewing has took place

where pick ends.

shape of marker

end point (X) of drawn marker.

end point (Y) of drawn marker.

shift caused by skew (to get parallelogram)

Gets the shift caused by skew (to get parallelogram)

pixel threshold to go from line to box

cursor region containing first point

trace used for peakpick cursor drawing

Gets or sets point for start of data on end of pick that's not being dragged.

Gets the style chosen(same as styleType except when 'Automatic')

Test if pack has started

Test if pack has moved since it was started

Gets or sets a value indicating whether the pick has been started.

Gets or sets the pixel threshold to go from line to box. If a drag is made on a plot, using Automatic , a horizontal line will remain horizontal, as long as the vertical distance between the start point and the current point is within this threshold. The same applies to a vertical line. This is a "mouse jitter filter" as customers cannot make a line perfectly horizontal or vertical

Style of symbol

Gets or sets the symbol for corners of marker

Gets or sets Image, which is used for "Image" style cursors.

Gets the offset applied to the image. This takes account of where the mouse was clicked within the image so that the drag starts without the image "jumping" to the top left corner at the mouse point.

Initializes a new instance of the class. Construct

Attach trace data to this pick. This allows PeakPick or ManualPeakPick style markers to snap the pick to real data. This must be set before calling , or using a PeakPick or ManualPeakPick style markers

trace, which is used for aligning a cursor to data.

start of pick (mouse down)

cursor input region containing start point Control which received the event Holds the shape to be drawn on an Adorner X,Y of start point The type of pick marker to create symbol to use

Start a pick, for dragging an image

The region. The shape. The point. The offset x, from the origin of the image to the mouse click point. The offset y, from the origin of the image to the mouse click point.. The style of the image marker. Must be either Image or GeometricDrawing

start of pick (mouse down)

cursor input region containing start point Shape which contains marker, to draw on an Adorner control X,Y of start point The type of pick marker to create symbol to use

end pick (mouse up)

Start and End points of the pick

Get the current marker start and end points

Start and end of the pick

Find the point in the data closest to ,

X data value (for example mass) to look for. Updated with the found value Y data value found. true if a point has been found. If false, no values are set for or

Find Y value of the nearest point on the trace associated with this cursor. For example, find the nearest chromatogram point intensity for a given retention time.

X value to find in the trace data (nearest) The Y data value at the neatest point to the supplied X data location

choose style of marker. Determines based on the region type, and whether the operator appears to be drawing a line or a box, based on threshold.

Determine if a line or box style should be used

The absolute x. The absolute y. The inner rectangle of the plot

The choose style when skewed.

The x difference. The y difference. The d skew. The absolute x distance moved. The absolute y distance moved. The inner.

move pick (mouse drag)

The shape. The point.

draw a marker (line or box)

The shape.

Draw the image marker into the rubber band shape.

The shape into which the image which will be drawn.

Draw the geometric marker into the rubber band shape.

The shape into which the image which will be drawn.

Draw a marker which has a vertical line And a triangle at the top. Used to show "current retention time" on a chromatogram.

Shape to which the marker's vectors are added

Draw a wide neutral loss marker.

Shape to which the marker's vectors are added The tangent of skew.

Draw wide horizontal marker.

Shape to which the marker's vectors are added The tangent of the skew angle.

Draw wide vertical marker.

Shape to which the marker's vectors are added. The tangent of the skew angle.

The draw fixed box marker.

The shape.

Draw box marker.

Shape to which the marker's vectors are added.

Draw a marker for adding a manual baseline peak to a chromatogram

Shape to which the marker is added.

Draw manual peak pick marker.

Shape to which the marker's vectors are added.

Draw peak pick marker.

Shape to which the marker's vectors are added.

Draw diagonal marker.

Shape to which the marker's vectors are added.

Draw a vertical marker.

Shape to which the marker's vectors are added.

Draw a horizontal marker.

Shape to which the marker's vectors are added.

Creates a bitmap which represents a density (heat map) plot.

Initializes a new instance of the class.

The traces. The color scaler.

Draw the traces using a bitmap

Bitmap to draw on The points plotted. The scaled x. The plot rect. The amplified. The min xgap. Compress this many traces into 1 pixel The .

Gets or sets the max enlargement. When using EnhanceSize, this sets the maximum size of a point plotted.

Gets or sets a value indicating whether enhance the size of points, based on intensity.

Draw all density plots, between certain intensity limits this is intended to permit ordering, so that "large data" can be drawn last.

The points plotted. The scaled x. The amplified. The min xgap. The bitmap. The band minimim. The band maximum. compress this many plots per pixel

Draw a circular or elliptical point, based on intensity.

The start pixel. The end pixel. The bitmap. The bit map y pixel. The color.

Access annotation

Access heading

Create data for designer mode

Emulate mouse down

Emulate mouse move

Emulate mouse up

Class designed to make a 2D or 3D map from a raw file

Gets or sets the mass limits of the plot. For PDA this will be a wavelength limit

Initializes a new instance of the class. default constructor

Initializes a new instance of the class. Copy constructor

plot to copy

Creates a new object that is a copy of the current instance.

A new object that is a copy of this instance. 2

Clear my data if it does not match another map To save space on undo stacks.

Erase all data tables

clean up ready for new data

object which will supply the data

Default for "max traces" which can be generated. See MaxTraces.

min valid value for "max traces" which can be generated. See MaxTraces.

If there are a large number of scans, the max traces limit is internally reduced But: will not be forced below this "hard min". Trace plotter expects at least 1000 traces, provided that may fit in the display range, for small bandwidth settings, so: values below 2000 could cause issues.

max valid value for "max traces" which can be generated. See MaxTraces.

Gets or sets the maximum number of traces which will be generated. value must be between 10,000 and 200,000. Default 25,000. Out of range values are forced "in range". Larger values can allow plots to be zoomed, without needing new data from the raw file, but may need more memory. Smaller values can cause more frequent data fetches on zoom, but use less memory. Small values (below MaxTracesMin) are not accepted, as: The could may get further reduced based n the number of scans in a arw file and: the plot attempts to keep at least 1000 traces for an accurate plot, especially at small bandwidth.

Fill data tables.

The data. The scans in file. The all scan time.

The get width of each trace for pda.

The data. The min mass. The .

loop through all the mass chromatograms, find largest at each point

first peak in scan to consider data for 1 scan Index into trace, where this result should be saved

Create data for a trace where masses in a band are summed

first peak in scan to consider data for 1 scan Index into trace, where this result should be saved

Create traces, where the average intensity over a mass band is used.

first peak in scan to consider data for 1 scan Index into trace, where this result should be saved

read raw data for map

object which returns data for the map

Class to perform extraction of map value from 1 scan

Gets or sets the index into "scan table"

Gets or sets a value indicating whether this is for the MS detector

Gets or set the scan to be analyzed

add a worker.

The work.

Pull some work from the queue.

Queue of work which is done in parallel

Process data for one batch of scans, based on queued record for parallel job

batch of scans

Add work to the work list. If there are insufficient background workers, assign more.

Collection of work New job to add

Create data table for one trace.

work items batched so far Work item queue The data. The index. True if all data needed. The count of scans which have passed filter The start time. The end time. True if detector is MS. The updated value of count

Create data table for one trace.

work item queue work items batched so far The data. The index. True if all data needed. The count of scans which have passed filter The start time. The end time. True if detector is ms.

Include data for one scan in the map table

Index for this scam trie, if this is MS data Scan to analyze

Analyze the entire raw file. Regenerate the map data.

Create a set of data to draw

object which will supply the data set to true if this has the same data limits (scroll range) as before. Default: false (suitable for opening a new raw file etc.) This is used to determine data compression only. No drawing is done by this method.

Gets a value indicating whether the data was generated at the resolution of the Bandwdth settings If not: A new data source is needed for each zoom of the mass scale.

Set annotation for each trace

Resets the Data to the Full Time and Mass Range

Draw the map, using data created with the last call to

Drawing surface

ensure that there is data for the current mass range

true if the data has to be changed

Defines information sent when new map data is prepared

Gets or sets a value indicating whether the limits of data (scroll bar range) are unchanged by this new data

This Event occurs when the new data is assigned to the Plot

The on data prepared.

The e.

This class defines an image label for a peak. Labels are drawn in priority order N.B. both position and intensity are optional if correct x,y can be given as label is added. When correct x,y is not known, position and intensity must be given, and convert must be called after filling label list

Initializes a new instance of the class. Create a copy of a label. This only copies one label (not the "Next" in list).

PeakLabel to copy

Initializes a new instance of the class. Default constructor

Gets or sets the image to be drawn

Class to manage a list of labels with images

Initializes a new instance of the class. default constructor

Initializes a new instance of the class. copy constructor

PeakLabel to copy

add a new label to the list

image for the label x coordinate of label (must be supplied, or converted from position/intensity) y coordinate of label (must be supplied, or converted from position/intensity) relative priority of label (default all same)

draw all labels in list

Drawing surface

test if label can be drawn, and set flags.

Drawing surface

use after test draw, to draw flagged labels only

Device context to draw into

draw all labels in list

device context if this is set, flags are set if this is set, drawing is only done for flagged labels

Render all labels in the list

The label rendering algorithm The renderer for an image label.

Sort all fixed position labels by priority, and draw

The label rendering algorithm. The renderer for an image label.

Draw one label

The label rendering algorithm. The render image label. The renderer for an image label.

Count how many nodes are "Fixed position" (not "AboveGraph")

The fixed position count.

An Interface for implementing the Pan mechanism of the plot controls - Enables interaction between Controls

Flag - true if panning has been enabled

Enable or disable panning mode

Pan interface

Target percentage to pan Direction to pan - either forward or backwards. A pan "forward" on plot (pull grah to right by panning hand cursor) results in a lower axis range being shown (as this pulls data into the plot from the left)

Pan interface

start of pan range end of pan range

An Interface for implementing the select mechanism of the plot Controls - Enables interaction between Controls

Retrieves Current Selection Status

Set Control Selection

Object that was raised the event wether to select or deselect the event raising control

An Interface for implementing the zoom machanism of the plot controls - Enables interaction between Controls

Set Scaling back to show full Plot

Expand vertical

true if graph is changed

contract horizontal scale by a factor

true if graph is changed

Expand horizontal

true if graph is changed

contract vertical scale

True if graph was changed

zoom all the way out in x.

The .

zoom all the way out in y.

The .

Class to supply data to an ion map. This class allows ion maps to be generated from any data, without any specific file format. The application using ion map could have to hold a large amount of data, if all data had to be sent to the map in one call. Instead, the ion map requests and processes data one scan at a time. These scans are typically fetched by the calling application or control from a raw file. They could also be generated from an internal data structure.

Gets or sets a value indicating whether this data is filtered

Gets or sets a value indicating whether the data source is the same. A data source is considered "Same" if no changes have been made which would affect the returned scans. This is a contract between the derived class and the ion map. After extracting data from a source, the map will set "same" to true. Next time it is asked to extract data, it may use cached data, when "same" is still set. If the derived class changes the source (for example changing a data file), it must set "same" false.

Gets or sets the scan number of the last scan in the data source

Gets or sets the name of the file which this data comes from

Part of ion map code. Incomplete: Do not use yet.

Part of ion map code. Incomplete: Do not use yet. Part of ion map code. Incomplete: Do not use yet.

Provides standard handling of key events in plot controls

A keyboard key has gone down

The control. The key. The plot. True if the key has been handled.

Draw a label, which has an image (bitmap, vector drawing etc.)

Gets or sets Label to draw.

Calculate the bounding box for the given label

Information for rendering, such as "DrawingContext" and Fonts. Flag - true if this label should be rotated The calculated bounding box.

Draw the label

Information for rendering, such as "DrawingContext" and Fonts. Bottom of the label Top of the label The x center of the label Flag - true if this label should be rotated

Defines primitive outline drawing, constructing a shape by a set of move and line actions.

Start a new series of lines

Point where to start the line

Draw a line, from last "MoveTo" or "LineTo" position, to this position

Position to draw to

Defines the outline of a shape used for rubber banding. The class permits a shape to be created from a series of lines. Can also define an image to be drawn, and it's location (from drag and drop of peak labels). This shape is designed to be rendered as an adorner, using the RubberBandAdorner class.

The last point either moved or drawn to

Gets or sets the shape of the rubber band

Gets a value indicating whether a rectangle has been added to this rubber band shape

Gets or sets Image. The image may be null. If it is not null, the supplied image is drawn at the ImageLocation

Gets or sets line of text, to be drawn at the location

Gets or sets the font to use for the messages

Gets or tests the size of the text

Gets or sets ImageLocation. This defines the top left corner of the image.

Gets or sets text location. This defines the top left corner of the text.

Gets or sets the color for rollover text

Start a new series of lines

X coordinate Y coordinate

Draw a line, from last "MoveTo" or "LineTo" position, to this position

X coordinate Y coordinate

Draw a rectangle

left X coordinate top Y coordinate right X coordinate bottom Y coordinate

Initializes a new instance of the class. Default constructor

Begin a new line

Point where to start the line

Draw a line, from last "MoveTo" or "LineTo" position, to this position

Position to draw to

Information returned when a peak baseline is manually adjusted on a chromatogram

Initializes a new instance of the class. Create an event for a updating a peak baseline If the start time is later than the end time, then start and end are re-ordered

X data position at left of baseline Y data position at left of baseline X data position at right of baseline Y data position at right of baseline

Gets the X data value at the start of the baseline

Gets the Y data value at the start of the baseline

Gets the X data value at the end of the baseline

Gets the Y data value at the end of the baseline

Drawing style for the map

a separate line for each trace

a separate colored line for each trace

as separate, with lines between traces

As wire, but 'solid' shape

shaded by intensity

as Shaded, but with lines as well

Optimized density map mode (similar output to Shaded).

This class produces a 3d style graph, which connects together a list of traces (class ) It is used to make 3d chromatograms or 3d spectra

Gets or sets the rendering style

Gets or sets a value indicating whether smoothing of density map plots is enabled. By default maps are drawn as solid blocks of color. Smoothing creates interpolated expansions of the Density plot

Gets or sets the color of frame lines

Gets or sets the color of axis grid lines

Gets or sets the color of right edge and front face

Sets the color for solid fill

Sets a value indicating whether to draw grid lines

Gets or sets a value indicating whether to use only black and white rendering

Sets a value indicating whether to highlight small values in density map

Gets or sets a value indicating whether to enable drawing larger points (circular ends) for larger signals on density plot

Gets or sets the factor for density scale. larger factors = greater enhancement at low end.

Sets a value indicating whether edges (front, right) are filled for certain styles Edges are filled for styles "Shaded" and "ShadedLined".

Gets or sets the maximum spot size, where spot size is controlled by intensity

Convert Bitmap to bitmap source.

The source. The .

Compress scale.

The scaled x. The points list. The amplified. The compress at x. The final point. The scaled y. The .

Initializes a new instance of the class. default constructor

Set Color scale for shading plot

A table of colors from 0% to 100%. Only exactly 6 colors currently supported

draw 3d map

Drawing surface

Draw the background items.

The graphics. The number of traces. The scaled x. The parallelogram. The final point.

Draw density map.

The graphics.

Native Methods.

Draws grid lines at major tick marks

The graphics to draw on.

Draw the right edge.

The graphics. The right side.

Draw the floor.

The graphics. The parallelogram. The scaled x. The number of traces. The final point.

Class to supply data to the map

Gets or sets the number of scans in the data source

Gets or sets the scan number of the first scan in the data source

Gets or sets a value indicating whether filtering is being applied to this data, so maybe not all scans will be mapped.

Gets or sets the low end of Mass range for the data

Gets or sets the high end of Mass range for the data

Return the start time (RT) for a scan

scan number the start time (RT) for this scan

Test if this scan passes an applications filter

scan number to test True if this scan passes the filter (should be plotted)

Get index information for a scan number

scan number A scan object, where only index information is filled

Get scan index and data

scan number returned scan (index and data)

Gets or sets a value indicating whether this is mass spec data for example: if PDA: sample at 1 "wavelength step" as apposed to MS data, where there is no fixed step between masses

Gets or sets a value which determines the mass banding (tolerance) for the plot

This class provides a complete 3d chromatographic plot, including a default heading. Data is assumed to be nominal (one point for each integer mass). There must be the same number of data points in each mass trace, and 1 mass trace for each nominal mass in the mass range. E.g. for scans 100 to 199, mass 40 to 45, there are 6 mass traces, each of which has 100 data points. The plot is rendered in a variety of styles, including simple 2d stack, 3d overlay and density plot.

part of scaling logic for expand vertical. Not supported yet.

Gets or sets the data type used for the right axis of the map. For a basic time against mass plot, this default to mass. For other 3d plots (such as ion map) other types occur, such as precursor mass

Arrangement of the plot. Supports several different drawing styles.

simple 2d stack (like multiple chromatograms)

overlaid traces, 3d projection

density map (flat projection)

Gets or sets the angle to tilt back trace up

Gets or sets the angle of skew for the axis

Gets or sets a value indicating whether to draw a backdrop

Gets or sets the layout: 2d, 3d or density plot

Gets or sets the 3d plotting style

Gets a table of 6 colors, representing 0% to 100% intensity (step 20%)

Gets or sets a value indicating whether to ignore colors set, and scale from white (0%) to black (100%)

Gets or sets a value indicating whether smoothing of density map plots is enabled. By default maps are drawn as solid blocks of color. Smoothing creates interpolated expansions of the Density plot

Gets or sets a value indicating whether grid lines are drawn at major tic marks on the axes

Gets or sets a value indicating whether to use a "log" color scale

Gets or sets the base for log scale

Gets or sets the maximum symbol size (bitmap pixels) for larger signals, when EnhanceSize is set.

Gets or sets a value indicating whether density maps draw larger points for larger signals

Gets or sets the fixed value for fixed scale

Gets or sets a value indicating whether to use base peak for full file (MS data only)

Gets or sets a value indicating whether to use fixed absolute scale

Gets or sets a value indicating whether chromatograms are base peak, else summed masses.

class for converting between scan numbers and RT (and back)

set conversion table (RT at scan)

Time array to use

convert scan to time

Scan index The time at the scan index

Gets the trace list.

Gets or sets the step between adjacent mass (or wavelength) plots. Mass band size.

Gets or sets the color for backdrop, which shows "outer frame" of 3d area

Gets or sets the color for lines drawn around filled regions in 3d plots.

Gets or sets the color used when "solid color fill" is requested

Gets or sets the high mass. Axis version of mass range (+/- 0.5 bins)

Gets or sets the low mass. Axis version of mass range (+/- 0.5 bins)

Gets or sets the class to do the rendering

Gets or sets the start mass. Start of mass range to show

Gets or sets the end mass. End of mass range to show.

Initializes a new instance of the class. constructor

Initializes a new instance of the class. copy constructor

Map plot to copy

return the number of traces for a given mass range

The mass range within which traces are counted distance between mass bands The number of traces that will be plotted for this mass range

create list of traces for graph This attaches the previously read data to a table of traces, and sets styling options the same for each trace

number of scans start of mass range to plot (range in z-axis 3D map, y-axis in density mapping end of mass range to plot (range in z-axis 3D map, y-axis in density mapping The start of the created data for the map (allows a slice of the data to be plotted) chromatogram for each scan reference to all zeros trace RT at each scan What trace type, used for what cursor to display data type for X Axis, such as "time" or "precursor"

Initialize trace list.

The number of scans. The n traces. The start mass. The end mass. The scan time.

Create traces from data.

The n scans. The scan data. The trace type. The x type. The first displayed trace.

Create traces from data.

The n scans. The scan data. mass trace which is all zero The trace type. The x type. The first displayed trace.

Initialize index to time.

The number of scans. The scan time.

initializes traces with fixed scales

The scale.

Creates a new object that is a copy of the current instance.

A new object that is a copy of this instance. 2

TODO: May Need Fix - The data needs to be regenerated.

resets traces with fixed scales

draw report

Drawing surface

Set fixed scaling

Fix scale value (100% value)

class designed to hold data for one line of a '3d' chromatographic map. The line holds 'float' intensity values for a set of scans in one mass band. the base class 'FloatTrace' holds the floating data, and is derived from Ctrace, so that it can be treated like a 2d graph trace, with inbuilt normalization functions etc. most of this class is in FloatTrace just need to advertise the data types for cursor input reasons, and add constructor

data type on x axis

get the largest data value (depends on data type)

The largest value in the data

get the largest and smallest data values (depends on data type)

The largest value in the data

Gets a value indicating whether can have negative peaks.

The trace x value type.

The .

The trace y value type.

The .

The trace z value type.

The .

The set x type.

The x type. The .

get the minimum X value in data to plot

The minimum value on the X scale

get the maximum X value in data to plot

The maximum value on the X scale

class to perform rendering for 3d map traces

Gets or sets the Graphics surface

Gets or sets the Pen to draw with

Gets or sets the Brush for solid fills

Gets or sets the Data for all traces

Gets or sets the Drawing style

Gets or sets the Tool to map intensity to color

Gets or sets the Color for edges of 3d map

Gets or sets the Color for lines of 3d map

Gets or sets a value indicating whether edges are filled

plot trace as solid vertical lines, with 1 colour

coordinates of current trace amplified current trace data position of "0" for this trace

Increase green. Reduce red 66% and blue 50%

original color green tint

plot trace as solid, with shades depending on intensity

coordinates of current trace coordinates of previous trace number of coordinates Amplified current trace data Amplified previous trace data scaling of trace being drawn scaling of previous trace (being connected to) If true, draw even if all intensities are zero If true, use a scale for colors. Else use a fixed color. If true: Fill the peaks (else wire frame only)

Fill the "open hole" under the surface at the front.

data for trace region of trace number of points trace number

Follow steps 1a or 1b and then 2 to use this custom control in a XAML file. Step 1a) Using this custom control in a XAML file that exists in the current project. Add this XmlNamespace attribute to the root element of the markup file where it is to be used: xmlns:MyNamespace="clr-namespace:ThermoFisher.CommonCore.WpfPlot.Controls" Step 1b) Using this custom control in a XAML file that exists in a different project. Add this XmlNamespace attribute to the root element of the markup file where it is to be used: xmlns:MyNamespace="clr-namespace:ThermoFisher.CommonCore.WpfPlot.Controls;assembly=ThermoFisher.CommonCore.WpfPlot.Controls" You will also need to add a project reference from the project where the XAML file lives to this project and Rebuild to avoid compilation errors: Right click on the target project in the Solution Explorer and "Add Reference"->"Projects"->[Browse to and select this project] Step 2) Go ahead and use your control in the XAML file. <MyNamespace:MyDerivedControl/>

Access the heading manager

Default constructor

Create the designer data

Access teh annotatiom

Access the scale

cursor

Emulate mouse down

Emulate Mouse moved

Emulate mouse up

Emulate key up

Create designer (demo) data

class for ion map

Gets or sets the order of this MS/MS mass table. For example: order 2=MS/MS and has 1 precursor mass

Gets a Table of MS/MS masses, must be filled by derived class of IonMapDataSource.

Mass for a particular MS/MS transition. Entry 0 exists for a scan of MS order 2, and is the first precursor mass. For MS order 3, there must be entry 1, etc.

Precursor mass index, (0 for the MS/MS mass) The precursor mass for the given index

Table of MS/MS masses, must be filled by derived class of IonMapDataSource

The mass table to copy

A strongly-typed resource class, for looking up localized strings, etc.

Returns the cached ResourceManager instance used by this class.

Overrides the current thread's CurrentUICulture property for all resource lookups using this strongly typed resource class.

Looks up a localized string similar to BP: .

Looks up a localized string similar to Area.

Looks up a localized string similar to Area Ratio.

Looks up a localized resource of type System.Drawing.Bitmap.

Looks up a localized string similar to Color table length must be same as points length.

Looks up a localized string similar to \n ,;@-.

Looks up a localized string similar to F:.

Looks up a localized string similar to Color length must be same as label stream length.

Looks up a localized string similar to Factor must be greater than one.

Looks up a localized string similar to Height.

Looks up a localized string similar to Height Ratio.

Looks up a localized string similar to NL:.

Looks up a localized string similar to BP: .

Looks up a localized string similar to m/z: .

Looks up a localized string similar to MA: .

Looks up a localized string similar to MH: .

Looks up a localized string similar to RT: .

Looks up a localized string similar to S#: .

Looks up a localized string similar to RMS.

Looks up a localized string similar to SN: INF.

Looks up a localized string similar to SN: NA.

Looks up a localized string similar to SN: .

Looks up a localized string similar to SU: .

Looks up a localized string similar to AA: .

Looks up a localized string similar to AH: .

Looks up a localized resource of type System.Drawing.Bitmap.

Looks up a localized string similar to %RSD = .

Looks up a localized string similar to R^2 =.

Looks up a localized string similar to RT:.

Looks up a localized string similar to Bc.

Looks up a localized string similar to Co.

Looks up a localized string similar to Cc.

Looks up a localized string similar to Pw.

Looks up a localized string similar to Rs.

Looks up a localized string similar to St.

Looks up a localized string similar to Sn.

Looks up a localized string similar to Sy.

Looks up a localized string similar to Tl.

Looks up a localized string similar to O.

Looks up a localized resource of type System.Drawing.Bitmap.

Looks up a localized string similar to W:.

Looks up a localized string similar to Null Scan reference in scanData array.

Looks up a localized string similar to normalModes must be same length as added traces.

Looks up a localized string similar to scaleValues must be same length as added traces.

A strongly-typed resource class, for looking up localized strings, etc.

Returns the cached ResourceManager instance used by this class.

Overrides the current thread's CurrentUICulture property for all resource lookups using this strongly typed resource class.

Looks up a localized string similar to O.

Event information for selecting a retention time from a plot

Constructor: Supply the retention tiem for this event

The time picked from the graph

The time selected from the graph

Class to draw a spectrum graph. A spectrum is defined as a stack of "Spec" traces, with a single mass axes.

Set the X data range of the plot

Gets or sets the color to use for profile line

Gets or sets the color to use for peaks which have no flags set

Gets or sets the color to use for saturated peaks (Stick style)

Gets or sets the color for reference flagged peaks

Gets or sets the color for exception flagged peaks

Gets or sets the color to use for shaded plots at 0%

Gets or sets the color for shaded plots, at 20% intensity

Gets or sets the color for shaded plots, at 40% intensity

Gets or sets the color for shaded plots, at 60% intensity

Gets or sets the color for shaded plots, at 80% intensity

Gets or sets the color to use for shaded plots, at 100%

Gets or sets the color for backdrop

Gets or sets the color for trace

Initializes a new instance of the class. constructor

Initializes a new instance of the class. Copy Constructor

Creates a Copy of the passed in Plot

Copy of Color table for non flagged peaks, per trace

The regular per trace color table.

Get the regular centroid line color which will be used for a specific trace

the trace whose line color is needed The color to use for "not flagged" peaks in this specified trace

profile per trace color

The profile color for each trace.

Get the line color which will be used for a specific profile trace

the trace whose line color is needed the line color which will be used for the specified profile trace

delete old tables TODO: May Need Fix: slightly different from base class, which wants to set the trace list to null. Probably should be the same

The clear spectrum traces.

initializes traces with fixed scales TODO: May Need Fix: differs from base class version (not sure why)

Set the trace to the following passed in colors

Trace index Regular trace color Profile trace color

Creates a new object that is a copy of the current instance.

A new object that is a copy of this instance. 2

Reset scaling to "auto".

set valid graph limits, when new data is set or a new range

Get axis name for the supplied name index.

The axis name.

Set the attributes for the border

Flag - true if the border should be drawn Color to use Flag - true if this is active

Draw the plot

WPF drawing area

Class to delete image labels

Gets or sets a label, such that any label matching it will be removed

Determine whether the given label should be deleted

a label of ImageLabel type true if the label should be deleted; false otherwise.

Clear annotation matching the given image label

image label object to be deleted

Contains X,Y data from a graph (in data space, not pixels) Contains the key for the symbol

Initializes a new instance of the class. Create an event for a mouse movement. Translates X and Y data from the plot

X data position Y data position Text which was attached to the marker (for example file name) Second text key attached to marker (for example peak name)

Gets the X data value at the mouse position

Gets the Y data value at the mouse position

Gets the key attached to this symbol

Gets the peak The key attached to this symbol

Extends plot brush with WPF conversions

Create a PlotBrush from a WPF Brush

Brush to convert The converted brush

Plot color to WPF color conversions

Convert a color to a plot color

color to convert converted color

Convert from a WPF color

Color to convert the converted color

Convert to a WPF color

Color to convert the converted color

Convert a list of colors to an array

colors to convert converted colors

Convert a list of colors to a list of plot colors

colors to convert converted colors

Convert a list of plot colors to a list of colors

colors to convert converted colors

Dash style converter for WPF

Create a PlotDashStyle from a (WPF) DashStyle

The WPF style to convert The converted style

Create a PlotDashStyle from a (WPF) DashStyle

The WPF style to convert The converted style

Convert a list of dash styles, from WPF format

Styles to convert converted styles

Convert a list of dash styles, to WPF format

Styles to convert converted styles

Conversion helpers for WPf

Initializes a new instance of the class. Construct a linear gradient brush from single color (no gradient)

Color for the brush

Plot line segment converter, from WPF format

Create a PlotLineSegment from a WPF line segment

The segment to convert X offset added to all coordinates Y offset added to all coordinates The converted segment

Conversions between WPF types and PlotCore types, for "PathFigure"

Create a PlotPathFigure from a WPF path figure

The WPF path figure X offset added to all coordinates (transform) Y offset added to all coordinates the created figure

convert segments in a Path Segment Collection into a list of PlotSegment.

The segments to convert. x value to offset all coordinates. y value to offset all coordinates. The converted segments.

Conversions between WPF types and PlotCore types, for "PathGeometry"

Create a PlotPathGeometry from a WPF PathGeometry

The WPF PathGeometry X offset added to all coordinates (transform) Y offset added to all coordinates The created Geometry

Convert figures.

The figures. x offset to add to coordinates. y offset to add to coordinates. The converted figures.

Extend plot Pen with conversions from WPF

Create a PlotPen from a Pen

Pen to convert The created pen

Initializes a new instance of the class. Construct a pen from a brush and width

Brush to paint this pen Width (points) of the pen

Type converters between WPF and plotting library

Create a plot point from a WPF point

Point to convert Converted point

Create a PlotPoint from a WPF point with an offset

Point to convert X offset added to the point. Y offset added to the point. The converted point

Convert a range of plot points to a range of WPF points

start of range end of range Converted point range

Convert from a PlotPoint to a WPF point

Point to convert The converted point

Conversions between WPF types and PlotCore types, for "PolyBezierSegment"

Convert from ploy bezier segment.

The bezier segment. X offset to add to all coordinates. Y offset to add to all coordinates. The converted segment.

Convert points.

The points to convert. X offset to add to all coordinates. Y offset to add to all coordinates. The converted points.

Conversions between WPF types and PlotCore types, for "SolidColorBrush"

Initializes a new instance of the class. Construct a solid brush from a color.

color for brush

Conversions between WPF types and PlotCore types, for Rect

Create a PlotRectangle from a

The WPF The created Rectangle

Convert to type

The rectangle. The rectangle as a

Convert to type

The rectangle. margin to prevent clipping issues at boundaries as WPF is floating point. Should be less than 1. The rectangle as a

This class includes helper methods to create spectra from various sources. For example: Create a spectrum plot from a raw file. Support various labeling features, including elemental compositions.

Get the spectrum at a specific time from a raw file, in the format "GraphicScan"

Name of raw file Time of scan The scan at the selected time

Get the label data (centroids) from a raw file

Raw file Scan number Data for that scan

Obtain "LabelStream" data from raw file for the constructed scan. Only applicable to certain instruments.

Raw File Name Scan to plot The centroids

Retrieve spectrum data from a raw file in the form of a scan

Raw file Flag whether or not to only retrieve the label data The scan number to retrieve Contains the updated maximum x data Contains the updated maximum y data Contains the updated minimum x data Contains the updated minimum y data The .

Retrieve spectrum data from a raw file in the form of a scan

Raw file Flag whether or not to only retrieve the label data The scan number to retrieve The .

Convert spectrum data to type graphics scan. Also calculates some statistics.

Scan Data from the raw file raw file stats for this scan Data for FTMS/Orbitrap centroids for profile data (can be passed as null) Flag whether or not to only retrieve the label data The scan

Convert spectrum data to type graphics scan. Also calculates some statistics.

Flag whether or not to only retrieve the label data Contains the updated maximum x data Contains the updated maximum y data Contains the updated minimum x data Contains the updated minimum y data Scan Data from the raw file raw file stats for this scan Data for FTMS/Orbitrap centroids for profile data (can be passed as null)

get segmented scan data.

The raw file item. The scan number. The stats. The is centroid. The .

GeneratedInternalTypeHelper

CreateInstance

GetPropertyValue

SetPropertyValue

CreateDelegate

AddEventHandler